Guide :Saws : 708715PK/JTAS - 10X50 - 1PK 3HP 1Ph Xacta JTAS - 10X50 - 1PK...

On/off switch Suddenly my table saw switch won't turn off. If I hold down off button, saw begins shutting down, but when I release finger from off button, saw turns on again. There are two adjustable dials inside swith housing. One says "test" "man" or "auto". This one is on test. Other notched wheel is set just below"18", but can be set higher or lower. Could either be adjusted to make magnetic contact of "off" switch respond correctly? Can dust be effecting contact? Looks clean, but maybe contact need to be cleaned? ThaNKS

Posted by clifff on Sep 21, 2008

Research, Knowledge and Information :


You Can Own the Original 'Just Two Years Away ... - Gizmodo


But because flying cars are perpetually “just two years ... Maybe there isn’t ... because—as Moller’s eBay listing points out—the FAA won’t let you ...
Read More At : gizmodo.com...

Full text of "Popular Science" - Internet Archive


texts All Texts latest This Just In Smithsonian Libraries FEDLINK ... Full text of "Popular Science" See other formats ...
Read More At : archive.org...

Watching Apple's New Shark Tank-Inspired TV Series Is Like ...


There’s the director counting down! There’s ... Of the two companies greenlit ... but having four judges swipe left or right on an app’s viability isn’t ...
Read More At : gizmodo.com...

Roughing It Smoothly V-10 #4 by Tiffin Motorhomes - issuu


Roughing It Smoothly® is a quarterly ... but there are options that won’t break your calorie ... Wayne Melvin bought his son a table saw when he was 10.
Read More At : issuu.com...

Adventures in 3d Printing | Technology | 3 D Printing


There are two kinds ... and start over at step #1. turn off the MakerBot. and will ... and then having to cool down again. but once it begins printing ...
Read More At : de.scribd.com...

Adventures in 3d Printing | 3 D Printing | Hacker Culture


There are two kinds of ... and they certainly won't want to tinker with the machine's ... an Arduino Mega2560 controller board with RAMPS 1. turn off the ...
Read More At : fr.scribd.com...

Charlotte sun herald - UFDC Home - All Collection Groups


Charlotte sun herald. ... But there is one achievement, which reflects his attention ... You won't want to miss all of the food choices, including
Read More At : ufdc.ufl.edu...

NWH-4-19-2013 by Shaw Media - issuu


... NWH-4-19-2013, Author: Shaw Media, Name: NWH-4-19-2013 ... but says the man is not due for release ... turn off utilities at the main switch ...
Read More At : issuu.com...

JuJa Italia


Top VIdeos. Warning: Invalid argument supplied for foreach() in /srv/users/serverpilot/apps/jujaitaly/public/index.php on line 447
Read More At : jujaitaly.net...

Suggested Questions And Answer :


On/off switch Suddenly my table saw switch won't turn off. If I hold down off button, saw begins shutting down, but when I release finger from off button, saw turns on again. There are two adjustable dials inside swith housing. One says "test" "man" or "auto". This one is on test. Other notched wheel is set just below"18", but can be set higher or lower. Could either be adjusted to make magnetic contact of "off" switch respond correctly? Can dust be effecting contact? Looks clean, but maybe contact need to be cleaned? ThaNKS


The contacts in the switch are burnt, replace them.
Read More At : 708715PK/JTAS - 10X50 - 1PK 3HP 1Ph Xacta JTAS - 10X50 - 1PK......

The triggerj switch is malfunctioning in my 10'' Ryobi miter saw. I took the switch apart and cleaned the contacts and it worked for about 5 minutes. I need to find a new trigger switch. My saw is an old one, it's a TS-2514. The switch is a SP215R. Any suggestions?


Contact Ryobi via their website and ask for details of a supplier near you. Ryobi are very good with parts for older models.
Read More At : Saws...

Bosch table saw GTS1031 won't start.


In case of this kind of questions you can only advise someone to go back immediately where they have bought the tool for warranty or exchange or money back. No other suggestions but few years to late to give the only right answer in this cause of question.
Read More At : GTS1031 10-in Portable Jobsite Table Saw...

I have powermatic pm2000 3hp 10" saw, when I try to turn on push on button , it blows the breaker. I have correct power. I have used this saw for 5 years no problems. I took magnetic switch apart, seems ok, contacts look, ok ,Is it possible capacitors gone bad in motor, or is possible too much sawdust got inside motor, which causes motor to short out? Any help would be greatly appreciated, My saw is my livelyhood.


There is a direct short some where.Unplug and turn the blade and listen to the bearings. One of the brushes might be worn down and be jammed against the armature. Five years of use and those brushes might be ready for replacement. If things turn out to be easy fix then changing brushes is not that hard.When you take them out you will see some small holes in the holders.When you put the new brush in the spring will try to push the brush back out,use a small piece of wire in the holes to hold it in.Next install the brushes back where they go.Check the armature out use a hacksaw blade to clean those grooves between the metal strips.Put the armature back in place and button it back together and pull out the keeper wires and your done.
Read More At : 66 10" 3 HP 1 Phase 230V Table Saw w/ 30" Accu-Fence &......

Motor will not start on my Ridgid table saw


Check the brushes and the commutator for wear and buildup between the insulated areas of the commutator..It should be clean and not full ofcopper residue.That will make the motor click only upon triggering the starter switch
Read More At : Reconditioned 10" Jobsite Portable Table Saw with Stand...

One of the contacts on trigger switch for 939 is stuffed


Its the whole switch package. I just ran into the same issue. Will try and disable the safety.... Not good idea for anybody. Try and find a new switch Part number 153207-01
Read More At : Dw939 Cordless Circular Saw 18 Volt 612"...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0653 seconds