Guide :Saws : 14" Band Saw with Stand

Motor power question

How does the horsepower effect the work?

Research, Knowledge and Information :


Stage Revolve (Motor and Power Question) | ControlBooth


Sorry, not sure where this should go. I am building a 16' (diameter) stage revolve. It will consist of floor mounted wheels upon which the platform...
Read More At : www.controlbooth.com...

Twin Tmotor power question - RC Groups


Oct 06, 2016 · Question Twin Tmotor power question Multirotor Drone Power Systems
Read More At : www.rcgroups.com...

Electrical Questions from AC-DC Motors - Freshersworld


Electrical interview questions from AC & DC motor principle and working . what is the principle of motor? Whenever a current carrying conductor is placed in an ...
Read More At : placement.freshersworld.com...

Electric motor power increase question | Electronics Forums


OK, I have a project I'm working on, where I need to increase the available stall torque of some existing motors, it's important not to change the...
Read More At : www.electronicspoint.com...

all motor power, questions! - ClubIntegra.com - Acura Integra ...


Hey guys im new to the thread and to integras. I just bought a 95 ls and the guy told me that it had aftermarket
Read More At : www.clubintegra.com...

Motor Power Equivalency Question. - Slot Car Illustrated Forum


Well, there's a technical mouth full. Let me try and explain. About the time I was having my FF050 motor spec'ed out (and, a huge thanks to all the help I got from ...
Read More At : www.slotcarillustrated.com...

Electric Kontiki motor power supply and PWM questions ...


Hello, I'm finally getting around to building an electric fishing Kontiki and have some questions about how to do so. First off an electric Kontiki is...
Read More At : www.electronicspoint.com...

Three Phase Circuits Quiz Questions | Electrician Exams ...


Three Phase Circuits Basic Theory: PolyPhase Systems: Single phase system supplying power to loads has its own limitations and has been replaced by polyphase
Read More At : www.electricianexampracticetests.com...

Power consumption when DC motor runs on battery - Electrical ...


I have small doubt about power supply selection for a running motor. ... Power consumption when DC motor ... Browse other questions tagged dc-motor switch-mode-power ...
Read More At : electronics.stackexchange.com...

AC Motor Control Circuits | AC Electric Circuits Worksheets


AC Motor Control Circuits; ... The follow-up question of how we may make the motor stop running is a very ... where there is physical access to the motor power ...
Read More At : www.allaboutcircuits.com...

Suggested Questions And Answer :


Rigid 14" Band Saw Stand Bounce


Yes, take it back to the store that sold it and get them to replace or repair the problem. Hope this helps!
Read More At : 14" Band Saw with Stand...

Wheels won't turn


OK I checked a couple sites and depending on the model number one of the motors is obsolete, the other is about 240.00 list. Are you sure the motor is bad? If so what I would do is if you have a local Grainger supply center give them the numbers off the motor and let them match it up with a Dayton motor. I didn't see anything special on the one that I looked at. It appears to have a straight shaft with a keyway for the pulley. Before I drove the 150 miles double check the motor and also it appears that it has a capacitator to check also. Let me know if I can help further but I wish I had better info for you.
Read More At : 14" Band Saw with Stand...

Motor replacment I have a 14" Delta band saw, model 28-255 The 1hp is over heating where its smoking and a sticky substance is coming out of the bottom of the motor. Delta says the motor for this band saw has been discontinued. Is there a replacement motor or can it be rebuilt.


Try to contact ereplacement . Or check out the motor from Baldor electric company. They have available motors. If you need band saw blade, my supplier is sawblade.com . Check them out.
Read More At : Machinery 14" Band Saw with 1HP Motor & Enclosed Stand...

Motor power question


Horsepower is the maximum power produced by the motor. Saws with high horsepower ratings are good for pattern cutting and cutting down thick stock. Higher horsepower also allows the saw to cut through thick stock without bogging down or burning the wood.
Read More At : 14" Band Saw with Stand...

Blown engine I have ten saws i rent out, and have had four motors blow in the past month. the saws are getting old, but are well maintained. When I rent them out, i send them with a can of premixed fuel, so the customer does not put regular gas in the machine. The premix is 50:1 using 2 cycle engine oil from Stens. My question is, Is there a better oil to be mixing with these older saws? Or is there anything else that could be scaring the piston and cylinder, and blowing the motors? (compression is @ 75psi)


Makita likes you to use at least 91 octane fuel and a synthetic oil mixture. the stens oils is garbage, i switched to the makita oil around 6 months ago and i havent had a problem. also, the wacker saws use the same motor and their piston heads are sleeved in carbon so they last longer and dont score the cylinder as fast as the stock makita heads. makita also makes a 100:1 mix hi performance oil you can use.
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

Followed the instructions that came with the saw. I cannot install the bottom belt guard because the motot shaft gets in the way. When installed, the belt does not hang plumb from the saw to the motor. I have adjusted the positon of both the saw and motor as far as they go. Could it be that the wrong sized belt was given to me?


This is very possible, especially if the box was opened and resealed before you purchased it.
Read More At : 28 276 14" Band Saw W/ 3/4 Hp Motor & Open Stand...

I have a rocwell 10" tablesaw , the motor has been disconnected by My idioyic brother , I need to reconnect motor back to table wiring , the motor has 9 wires that are all labeled 1-9, I need a diagrm


Go to ereplacementparts.com they have diagrams that will help you. and the diagrams are FREE...
Read More At : Saws...

Owners manual delta 28-276 - Delta 28 276 14" Band Saw W/ 3/4 Hp Motor & Open Stand


Check this site: http://bandsawmanuals.com for free downloadable delta manuals.
Read More At : 28 276 14" Band Saw W/ 3/4 Hp Motor & Open Stand...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0548 seconds