Guide :Saws : Saws

How to keep the blade guard off the Circular saw blade when in use?

I have a 1200 Watt Power and Performance (B and Q) Circular saw,but no instructions, The blade has a slide over guard when notinuse,butIdon't know how to keep it off the Blade when I want touseit,Also,do you know where i can view instructions on line?

Research, Knowledge and Information :


How to Use a Circular Saw: 13 Steps (with Pictures) - wikiHow


How to Use a Circular Saw. ... Keep your saw guard in ... This is because of the blade turning and you don't want the blade to go flying off if the nut is ...
Read More At : www.wikihow.com...

How to Replace the Blade Guard on a Porter Cable Circular Saw ...


How to Replace the Blade Guard on a Porter Cable Circular Saw. ... The repair will help keep your saw blade properly covered when it's not actually cutting, ...
Read More At : www.ereplacementparts.com...

How to use a circular saw - YouTube


Dec 07, 2011 · A basic tutorial to familiarize yourself with using a circular saw. Plus, an illustration of kickback. My apologies for the whine of the leaf blowers in ...

How to Change the Blade in a Circular Saw - YouTube


Nov 14, 2013 · justaz.com productions, with At Home Repairs, demonstrate how to change the blade in a circular saw. Learn the procedure for taking the old blade out and ...

How To Use a Circular Saw brought to you by BARELYBAD


Blade guard ... If you don’t want to use a circular saw, ... and you need to keep in mind that injuries from ...
Read More At : barelybad.com...

How to Change a Circular Saw Blade | This Old House


If you're unsure, refer to the arrow on the saw's blade guard. 6 Use the blade wrench to tighten the arbor nut until it's snug; ... How to Change a Circular Saw Blade.
Read More At : www.thisoldhouse.com...

Circular Saw Tips and Techniques | The Family Handyman


Learn how to use a circular saw safely and ... Circular Saw Tips and ... it doesn't take much effort to keep the blade on track. But if you get off to a ...
Read More At : www.familyhandyman.com...

circular saws for safety. - University of Hawaii at Hilo


General Safety Rules • DANGER-- Keep ... Keep your body positioned to either side of the saw blade. • Check lower guard ... metal or masonry cut-off wheels. If ...
Read More At : hilo.hawaii.edu...

10 Circular Saw Secrets: DIY GUY - Popular Mechanics - How ...


Oct 29, 2009 · 1. Inspect the Saw. Before each use, run a quick safety check on the saw. Be sure the lower blade guard retracts smoothly and snaps back when released.
Read More At : www.popularmechanics.com...

Suggested Questions And Answer :


How to keep the blade guard off the Circular saw blade when in use?


What is (B and Q) stand for ? This is a circular saw or a table saw, or a miter/chop saw?
Read More At : Saws...

How do I fix my spring loaded lower blade guard on my circular saw


I need to know the make and model of your saw in order to help you.
Read More At : Saws...

Brand new saw. I put on the blade but it hits the safety guard?


I would return it.
Read More At : Saw. 13-Amp 7-1/4 in. Circular Saw CSB133L...

Circular saw blade rubs on the guard


Remove the blade and check for the inner flange that should be behind blade. also there might be a ring underneath the inndr flange. or check to make sure the flange is installed correctly.
Read More At : Ryobi...

I have a Craftsman 7 1/4 circular saw Model 315.10851 that I bought around 1980. It has been a reliable tool for numerous home projects over the years. I recently put a masonry blade in it to cut landscaping stones. It worked fine at first, then the blade started slipping. When I tried to tighten the bolt the blade the motor turns even when I hold the blade. I realize the problem is a result on not using the "blade washer" that has a flat spot which matches up with a flat spot on most blades. The masonry blade had only a circular opening so I didn't use it. The problem now is how do I get the masonry blade off of the saw?


Is there no armature lock on this model?
Read More At : Saws...

Circular saw motor turns when tightening saw blade


Insert a tool such as a screwdriver across the blade guard and against a tooth to prevent blade rotation, then tighten the blade nut. Be sure to remove the wedging device before operating the saw
Read More At : #Fury 7 1/4" Mp Circular Saw...

Ryobi TSS100L blade guard spring


I think what you are refering to is a circlip washer , and can only be fitted with ( CIRCLIP PLIERS ) do you know any Michanics or Engineers as they are bound to have a set in their toolbox ,on the other hand you can buy them. What they do is work in the opposit way normal pliers do when you squees the handles together the jaws open,therefor opening the (CIRCLIP ) and allowing you to place it over the pin and into the recess. Hope this has been of some hellp goodluck T.C.
Read More At : Saw. 13 Amp 10 in. Sliding Compound Miter Saw with Laser......

My saw problem has to do with changeing the blade. I'm useing a thin kirf blade. When I change the blade I have to put a wrench on the arbor next to the pulley to keep the arbor shaft from turning when I loosen the nut to remove the blade. I try to put a block of wood in the teeth of the blade to hold it while loosening the arbor nut with the wrench. The arbor nut turns with the arbor shaft and the blade doesn't move. I've used this blade for a few years without a problem. When I use my dadoe stack it does the same thing. The arbor shaft turns with the arbor nut when trying to loosen the nut to remove the stack. Any suggestions on what to do or whats happening?


The nut is binding on the arbor because the threads are buggered up or clogged with something. It could be the nut (which is probably brass and soft) or the arbor (which is steel). If it got a little cross threaded, the damage will be on the nut. It might be the arbor if the arbor took a whack. Once you have it apart you should be able to see it - although the damage might be pretty small. You aren't likely to have a tap and die to run through the threads, but you can probably fix it with a little rotary tool (like a dremel) using a small disc. If it is the arbor you can use a triangular file. Or you can buy a new nut. I hope this helps.
Read More At : 10" Table Saw...

To get the blade guard on a Ryobi circular saw to stay up.


Hello. The blade guard is specifically designed to not stay up but instead to only come up as the wood pushes it up. This is a problem when you are trying to do a plunge cut but it is a safety feature. Joe
Read More At : 18v One+ Circular Saw P501 18 Volt V 1 Plus...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0795 seconds