Guide :Saws : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw

Makita 6410 petrol disc cutter

My saw wont start its a 2007 model can you help??

Research, Knowledge and Information :


Makita DPC6410 Petrol Disc Cutter like stihl saw ts410


Makita DPC6410 Petrol Disc Cutter like stihl saw ts410 in Business, Office & Industrial, Industrial Tools, Cutting & Sawing Tools, Saws | eBay

Makita DPC6410 petrol saw Disc Cutter (not Stihl) WV6 Or DY8 ...


MAkita 6410 cutter, similar to a still Good working order Collect from Perton, near Wolverhampton Or Wordsley, near Stourbridge | eBay!

Makita DPC6410 12inch/305mm Petrol Disc Cutter (DPC-6410)


Makita DPC6410 petrol 12"/305mm disc cutter. Available with or without general purpose diamond disc. This machine is popular with civil engineers, bu..
Read More At : www.toolstop.co.uk...

Makita DPC6400 Petrol Disc Cutter - ptc tools.co.uk


Makita DPC6400 Petrol Disc Cutter: ... Makita Spare Parts Centre > Makita Spare Parts Centre > Makita Outdoor Power Equipment Spare ... PISTON RING DPC6400/6410: £12 ...
Read More At : www.ptctools.co.uk...

MAKITA DPC6410 12"/300mm 64cc Petrol Disc Cutter with Diamond ...


MAKITA DPC6410 12"/300mm 64cc Petrol Disc Cutter with Diamond Blade Tips. This improved disc cutter benefits from technological innovations such as the microchip ...
Read More At : www.worldofpower.co.uk...

makita dpc 6410 - YouTube


Jul 25, 2014 · makita dpc 6410 Darren Frost. ... Makita 14" MMR 4-Stroke Power Cutter - Duration: ... Evolution 305mm Disc Cutter: Evolve from Petrol Disc Cutters!

Amazon.co.uk: makita petrol saw


1-16 of 98 results for "makita petrol saw" ... LTD Description Makita EK6100 61cc 12inch Petrol Disc Cutter - Is a ... Service Kit for Makita 6410 Petrol Saw ...

Makita UK


Stone Cutter; Stone Saw; Petrol Disc Cutter; Wall Chaser; ... DISC CUTTER ACCESSORIES ... DISC DPC6200/6410/7311/7301: 169:
Read More At : www.makitauk.com...

Makita UK


Petrol Disc Cutter; Wall Chaser; Stone Cutting; ... DISC DPC6430/7331/8132/6410/73: 248: 108151350: ... Contact Makita! 01908 211678.
Read More At : www.makitauk.com...

Suggested Questions And Answer :


Makita 6410 petrol disc cutter


First of all, make sure you have followd the correct start up procedure. (1)Throttle on and locked in start position, (2)choke on and pull a few times. Saw should fire briefly and cut out. (3)Now switch to idle (half choke if applicable) and pull another couple of times. Saw should now fire and run. If you have pulled it too many times in the full choke position you will have flooded the engine. To rectify this you will need two people. One of you should hold the machine steady on the ground with no choke on and throttle fully open. The other should also steady the machine and pull the starter in quick succesion. This could take ten or so pulls but it should start the engine in the case of flooding. Sometimes it will splutter a couple of times before fully starting and it will normally bog down a bit for the first few seconds as it spits out the excess fuel/oil mix. If you got to point (3) as it shown above, and then the saw wouldn't start, or hadn't fired and died then there could be a few different problems. basic checks are for, clean filter, fresh/clean fuel, clean spark plug (ie, not oily/choked with carbon build up). When checking the spark plug, if it has fuel/oil mix on it then ther is probably aeither a compression problem/air leak or no spark. To check for a spark leave the plug unscrewed but fitted into cap, rest it against a metal part of the saw and pull the starter with the elec switch on. You should see a healthy blue spark. WARNING, do not rest the spark plug near the plug hole as if it does spark it could ignite any fuel/oil mix that is pumped out of the cylinder. I've had many a singed eyebrow from this happening. If there is no spark, check to make sure the cap is attatched securely to the lead,and try repacing the plug. If this doesn't help you will need to get the coil, ht lead and wiring tested.
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

Cutter wont stop stalling - Makita DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw


Check for holes and tears in fuel lines especially at bends and fittings. Typical Fuel System: HTH Lou
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

I have makita petrol stone cutter.it starts but wont take revs


It needs more gas adjust the screw on the carburator
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

I am trying to rebuild the 2 stroke engine from a makita disc cutter DPC 6410, does anybody know where i can get a big end bearing or complete crank, makita are asking for extorunate prices?


Have you checked with a Bearing House for a repacement bearing?
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

I need a piston and barrel for a makita dpc8112 stone saw


The cylinder and piston sell in a kit under part number 326-130-051. You can find it on websites like http://www.ereplacementparts.com/ but it costs $317 plus shipping. You may do better to find a local Makita service center that can order the part for you. Go to the Makita website at www.makitatools.com/en-us/Modules/Home/Default.aspx and look under the Services tab for a service center search box.
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

Blown engine I have ten saws i rent out, and have had four motors blow in the past month. the saws are getting old, but are well maintained. When I rent them out, i send them with a can of premixed fuel, so the customer does not put regular gas in the machine. The premix is 50:1 using 2 cycle engine oil from Stens. My question is, Is there a better oil to be mixing with these older saws? Or is there anything else that could be scaring the piston and cylinder, and blowing the motors? (compression is @ 75psi)


Makita likes you to use at least 91 octane fuel and a synthetic oil mixture. the stens oils is garbage, i switched to the makita oil around 6 months ago and i havent had a problem. also, the wacker saws use the same motor and their piston heads are sleeved in carbon so they last longer and dont score the cylinder as fast as the stock makita heads. makita also makes a 100:1 mix hi performance oil you can use.
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

My makita demolition hammer model hm1500 does not strike anymore


Try adding some hammer grease, Part # A-90582
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

Broken pull cord


Yeah you will have to replace it. they sell a kit for it,
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

I need to find a parts manual for a Makita 14" dpcc7311 / 0510 109385, any ideas


Dolmar/Makita http://charlotte.preferredpower.com/DOLMAR/Browse.htm The power cuts use Dolmar numbers. I'll wager one of the -7314s is yours. HTH Lou
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0967 seconds