Guide :Saws : Saws

Reciprocating saw stopped working while cutting

I have had this saw for only a few years to do non-commercial projects around my house. The other day, I was sawing up some treated 2x4s to dispose of them and part way through it just siezed up with the blade fully retracted into the housing. I checked the electrical cable by plugging it in to several other working outlets to no avail. I cannot get the housing apart where the motor resides. The manual has no troubleshooting information. Thanks for any advice you can provide.

Research, Knowledge and Information :


Reciprocating saw died - Houzz


While cutting through a pipe my Craftsman reciprocating saw just stopped. It didnÂt make any unusual sound or smoke or do anything out of the ordinary. It just stopped.
Read More At : ths.gardenweb.com...

Reciprocating Saw - ALCE


Do not place excessive pressure on the saw while cutting ... When cutting with the reciprocating saw, ... The blade has stopped moving before the reciprocating saw is ...
Read More At : www.alce.vt.edu...

Reciprocating Saw Uses | The Family Handyman


Reciprocating Saw Uses. ... Dust and debris can shake loose while cutting in older ... Remember this when working on ladders. When cutting through pipes or ...
Read More At : www.familyhandyman.com...

11 Amp Reciprocating Saw with Case - The Home Depot


Makita Reciprocating Saw is ideal for cutting metal ... 11 Amp Reciprocating Saw with 6 ... the lever for blade release snapped off while I was changing blades so I ...
Read More At : www.homedepot.com...

Heavy Duty Reciprocating Saw Shootout! | Pro Tool Reviews


While cutting is slower with a greater number of ... reading Heavy Duty Reciprocating Saw Shootout!, ... when its working. are they made with plastic gears these ...
Read More At : www.protoolreviews.com...

The 5 Best Reciprocating Saws Reviewed | Product Reviews and ...


The 5 Best Reciprocating Saws ... it’s difficult to change the speeds while cutting. ... that blade wore out quickly or that the saw stopped working after a couple ...
Read More At : www.top5reviewed.com...

Powered Hand Tools - Saws - Sabre, Jig and Reciprocating ...


Hold reciprocating saw with both hands. Remember sabre saws cut on the up stroke. Secure and support stock as close as possible to the cutting line to avoid vibration.
Read More At : www.ccohs.ca...

Milwaukee sawzall problem...anyone else? | Fine ... - Breaktime


My saw started cutting out on me after a ... then completely stopped working, ... to the repair shop and still every once in a while it just would not work ...
Read More At : forums.finehomebuilding.com...

Suggested Questions And Answer :


Reciprocating Saw / Stopped Working (No Response)


Many of my power tools that have stopped working, it has always been the "ON-OFF" switch that has been the proplem. Try blowing out the bugger, but watch that you don't loose some of the contacts. Never had brushes actually wear out, but did have one wire break off the brush.
Read More At : 8.0 amp Reciprocating Saw...

Hand jig saw stops cutting - makes whirring noise - then restarts


Jig saws are not made to cut through aluiminum espescially that size. That is really thick and it sounds like you have worn out the motor trying to cut it. If the saws are hot. Let them cool down then proceed but like I metioned before you are putting a lot of stress on something not made to cut aluminum even with a metal cutting blade
Read More At : Saws...

My Makita DSS610 18v cordless circular saw stopped working mid cut. I changed the battery to another, fully charged, one but still nothing. Tried again next day, with both batteries, still nothing.


Http://www.mtmc.co.uk/Makita-DSS610-Spare-Parts__p-75682.aspx maybe the autostop protection in one of the carbon brushes has been activated turn position 13 loose with a screwdriver its easy to remove and replace look this link for the position numbers . Makita DSS610 Spare Parts
Read More At : Makita...

My recip saw just quite working I was cutting and


Hi,The switch has gone bad and the contacts are gone...you will need to replace the switch...heatman101
Read More At : Dewalt...

My ryobi saw seems to be dying. I am trying to cut a piece of plywood and it seems to be working at full strength until I start cutting. As it starts cutting it slowly dies down to the point that it stops midcut. Is this likely something wrong with the battery, blade, or saw? What is an easy fix?


Need to replace battery(not holding charge
Read More At : 18v One+ Circular Saw P501 18 Volt V 1 Plus...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0853 seconds