Guide :Saws : Saws

My table saw will turn on, but sounds very loud

I used my table saw to rip a few pieces of wood a few days ago, normal work, nothing fancy. Then today I went to use it and when I turned it on it sounds super loud. What could the problem be? The blade looks fine and turns, it just sounds louder than normal.

Research, Knowledge and Information :


I have a table saw model 152.221240. It makes a loud ...


I own a Craftsman table saw model 152-221240. It has had less than 10 hours of use. It recently started making a loud screeching noise when I turn it on.
Read More At : www.shopyourway.com...

repair - Why does the blade of my table saw stop? - Home ...


Why does the blade of my table saw stop? ... turning the shaft seems to turn the motor without the slippage I saw before. ... it sounds worse.
Read More At : diy.stackexchange.com...

Should I be concerned that the furnace fan is making a loud ...


Should I be concerned that the furnace fan is ... the fan sounds makes a rhythmic tapping -very- much ... My table saw does this. Starts out a loud 60 Hz hum ...
Read More At : diy.stackexchange.com...

Why is a table saw quiet but a circular saw loud ... - Home ...


Why is a table saw quiet but a circular saw loud? ... and what is the loudest sound I can listen to before it hurts ... Why Universal Motors Turn on the Appliance ...
Read More At : home.howstuffworks.com...

Is Your Table Saw Motor Stopping, Stinking, Smoking or Silent?


Is Your Table Saw Motor Stopping, Stinking, Smoking ... If you have a benchtop or small portable table saw you can slowly turn it ... Loud noise table saw ...
Read More At : www.toolerant.com...

Table Saw Motor Problem - by pmulry @ LumberJocks.com ...


I've run into a problem with my table saw that I need some help ... When I turn it on, the motor makes a loud buzzing sound like it always ... It’s very odd, ...
Read More At : lumberjocks.com...

New Quiet Table Saw - Woodworking Talk


New Quiet Table Saw. ... the neighbors don't want to hear my saw which whines disturbingly loud even before the ... I sounds like you need a belt driven table saw.
Read More At : www.woodworkingtalk.com...

Suggested Questions And Answer :


My table saw will turn on, but sounds very loud


Possibly bearing wear, or the blade rubbing against the guard/housing. Unplug the saw and spin the blade slowly by hand, if it feels notchy then I would suggest bearing wear. if it only seems to feel notchy in places then it could also be damaged gears.
Read More At : Saws...

I am borrowing my brothers Craftsman model 137.218240 table saw. Unfortunately, it has a on/off switch problem (I believe). Yesterday, I was able to use it all day although, at first, I had difficulty getting it to turn "on". After about a dozen attempts (with no noise coming from the "on" switch activation) I called my brother who verified that the saw had this problem the last time he used it. He suggested I keep trying and I did and several activations later I heard a "thunk" noise twice (kind of like a locked rotor type sound), then finally it turned on a few trys later and all was well yesterday, just cross cutting some thin laminate flooring. However, this morning, same problem! However, after getting it going for two small cuts, I now cannot get it going, I just get the occasional "thunk" or momentary blade spinning! My questions are as follows: 1. Can I get inside this saw to see whether I can either repair, replace or bypass this switch myself. 2. Are you familiar with this type of problem and know of a solution? Manufacturer defect? By the way, the saw is not under warranty and Sear's service center is way too far away for me. also, this problem exists regardless whether I'm using an extension cord or not so I know it's not a low-voltage issue. Thanks in advance, Wayne


You can chec wiring or switch with an ohmmeter to determine if it is bad. You should be able to remove a few screws to access the inside of the saw fairly easily. You can easily by-pass the switch by twisting the wires together. Though it will have to be untwisted to shut off again. You could just unplug it. There isn't much to these.
Read More At : 10" Table Saw...

Bosch table saw model 4000


It sounds like the pinion on the armature and or gear are stripped. The only way to find out is to tilt the blade and remove the motor housing from the diaphragm and check it. If replacing the armature I would recommend also replacing the bearings and brushes as preventative
Read More At : Saws...

Ridgid saw R4515 upon start up shriking sound then every few blade turns a scraping sound what is it?


Change belt .... follow required maintainance ...
Read More At : 10 in. 13-Amp Professional Table Saw R4512...

Craftsman model 137.415030 10 in portable table saw won't turn on. It is getting power the switch sounds like it is working ok but it won't turn on. The reset button ,does not appear to do anything.


My table saw motor just stopped.. What do I do? - The WoodenBoat ... forum.woodenboat.com/showthread.php?...table-saw...I... WoodenBoat Apr 6, 2013 - 23 posts - ‎20 authors Does the motor have an internal thermal cutoff switch? ... Auto reset on a table saw, now that would be scary. ... A Craftsman, I think. ... The saw is a Grizzly 1022Z contractor-style saw about 10 years old. .... After the motor cools down the switchneeds to be pressed to restart the motor, it won't start suddenly ... My table saw stopped, the reset button won't reset. What ... www.shopyourway.com > Manage My Life > Questions It is a Craftsman Table Saw Model 137.248880. ... I pressed the reset button and the saw restarted. I continued ... My table saw stopped, the reset button won't reset. ... One was just the switch the other the rocker switch, identical except in cost. Craftsman 10 table saw motor stalled - Yesterday's Tractors www.yesterdaystractors.com > Discussion Forums > Tool Talk
Read More At : 21802 10-inch 13-amp Portable Table Saw...

I have a Craftsman table saw a few weeks back had problems getting the saw to run....would have to hit the switch several times to make it run. Once it was running it was good until I shut it down, then I would have to hit the switch 5 or so times to get it to run again. Today it did the same thing and now just wont run. The blade turns freely by hand and is not binded or anything. Does this sound like a bearing? Brushes?


Replace the switch? Hello!
Read More At : 10" Table Saw...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0604 seconds