Guide :Saws : DW824 5" Electric Angle Grinder

Why does my dw831 grinder keep tripping circuit breakers?

When you plug in the dw831 grinder, and then pull the trigger, the grinder runs for maybe five seconds, makes a terrible noise in the process, almost like a three phase motor that is single phasing, then the circuit breaker will trip. what is up?

Research, Knowledge and Information :


Why does my circuit breaker keep tripping? - Climatemakers


Why does my circuit breaker keep tripping? Breakers are a safety device. It is designed to protect not only the equipment but the wiring and the house as well.
Read More At : www.climatemakers.com...

Why Does My Circuit Breaker Keep Tripping? | George Brazil


Why Does My Circuit Breaker Keep Tripping? 2013 Apr 19. ... and want on-site help with your circuit breakers or to check your wiring, contact George Brazil. ...
Read More At : georgebrazilplumbingelectrical.com...

Why Does My Circuit Breaker Keep Tripping? - Kolb Electric


Constant circuit breaker tripping is ... you have an overloaded circuit. You want to keep the ... Short Circuits and Tripped Breakers. A short circuit is a ...
Read More At : kolbelectric.com...

Why does my circuit breaker keep tripping? | Reference.com


Why does my circuit breaker keep tripping? A: ... Keep Learning. How can I reset my circuit breaker? ... Circuit breakers in the home are often rated for 15 or 20 ...
Read More At : www.reference.com...

20 Amp breaker keeps tripping on 7" grinder startup ...


20 Amp breaker keeps tripping on 7" grinder ... Each grinder is on its own circuit but the breakers are still tripping. ... Assuming I keep the circuit at ...
Read More At : www.electriciantalk.com...

Electrical Fuses from Cooper Bussmann - CableOrganizer.com


Electrical Fuses. Wonder why the circuit breaker keeps tripping? Check out our guide below! ... My Circuit Breakers Keep Tripping, Why is This Happening?
Read More At : www.cableorganizer.com...

Top 10 FAQ | Why Does My Circuit Breaker Keep Tripping ...


Jan 02, 2013 · ... Why Does My Circuit Breaker Keep Tripping? ... about Circuit Breakers. Q: Why does my circuit breaker keep ... about Circuit Breakers, ...

Why Circuit Breakers Trip and Fuses Blow - The Spruce


An overloaded circuit is the most common reason for a circuit breaker tripping. It occurs when a circuit is ... Easily Trace Circuit Breakers with a Circuit ...
Read More At : www.thespruce.com...

Suggested Questions And Answer :


Why does my dw831 grinder keep tripping circuit breakers?


Try checking the brushes. to do this: remove the 2 small covers on the left and right side of the tool and push aside the coil spring holding in the brush. the brush should freely pull out of the holder. when you have the covers off, look for charring or melting. and after the brushes are out, rotate the arbor to move the armature inside and look to make sure it's not charred. if that doesnt help, take apart the handle and look for melted or exposed wire. dewalt likes to pack the wires in tight among the screws and sometimes the normal vibration of the tool will cause a screw to cut into a wire and short the wire. new brushes and holders (if melted) are usually around 20 dollars US
Read More At : DW824 5" Electric Angle Grinder...

The electric keeps tripping in my house, why is this?


It is something that is being pluged in or a short in 1 of the plugs on that circut
Read More At : DW824 5" Electric Angle Grinder...

Here is an interesting one. Every now and again we get a momentary loss of power to 3 different lines in our house (all downstairs). Lately the power outage has lasted longer. When I go out to the panel all the breakers are set. Even when I trip them and reset the power stays out. A couple day ago it happened while preparing dinner and my wife says, "Is the oven working. The oven clock was lit so it appeared to be working but when I spun the dial on the oven temp control the power came back to the lines that were down (oven on it's own breaker). Now, whenever we lose the power we turn the dial and get the power back. Three separate circuit breakers are affected by this situation. They are not close to each other on the main panel. More info: Once when the power was out I got a volt meter and checked the power going INTO the breakers. Every breaker was set and power from the street to the breakers was normal. But still out in the house. We did have a ton of rain two weeks ago so maybe there is some residual moisture.


Moisture outside has nothing to do with this. You either have power to the service panel or you don't. There are a few things that can cause these type problems. My first guess would be the problem is right there in the service panel. First turn the main OFF. Then remove the breakers that are being effected, one at a time, and look carefully at the connection on the back where they plug into the main service bar. A loose or burnt connection here will cause exactly what you are experiencing. A breaker that has any indication of it overheating should be replaced. If the main bar is burnt it must be cleaned. If you see any indication that water has entered the service panel then you may very well need to have the service panel replaced if the damage is severe. Another possibility is that you have a junction box somewhere in the attic with some loose wiring. This can be very dangerous as the wiring will overheat from arcing. Move the stove out from the wall and take the stove outlet apart and inspect it to make sure there is no loose wiring in there. As the stove has some effect on this it is highly suspect. I highly recommend you call a licensed electrician to diagnose this problem if you cannot find the problem yourself. This can be a very dangerous situation that may burn your home down. It is simply not worth taking any chances even if you have to spend a few hundred dollars to solve this mystery. Have this fixed ASAP.
Read More At : DW824 5" Electric Angle Grinder...

Everytime i plug something in my main electrics keep tripping the main rcd swich it can be anything from my iorn/washing machine etc my tv/fishtank and computer are all fine i have tryed different plugs but it still happens


Possible bad receptacle shorts out when something plugged in
Read More At : DW824 5" Electric Angle Grinder...

Ryobi circular saw --it keeps tripping my breaker


I would inspect the cord before doing anything, checking the leads for signs of scarring which could be due to leakage/incorrect grounding due to damaged internal wiring. The saw could be dangerous to operate so take care and make sure you have continuity after all is said and done that way you don't have to take the saw back apart.
Read More At : Circular Saw W/Dual Laser...

Electricity trip whenever i on my makita grinder


Check what's shorting to ground. remove the brushes and use a meter to "ring" out the motor circuit. maybe somebody sliced through the cord.
Read More At : GA7001L 7" and Larger Electric Angle Grinders...

Need help with my angle grinder. It quit working and the switch was bad . I replaced it . Not sure on where all the wires go. I have blk to blk and wht to wht. The wire coming from the electronic pack ( blk wire is on the switch with the other blk wire coming threw the switch from power. a red light flashes on the electronic pack when I trip the switch. It will not run or try to run. Is the electronic pack bad??? Do you have an electrical drawing and what do you think is wrong with it. Help. Michael Anderson


No its the brushes it was never the switch its runs at 9000 rpms the brushes ware out fast but this is a good tool save it
Read More At : 469 WE14150Q 01451 6" GRINDER 120 AMP 9000 RPM QUICK CHANGE......

How do you change the grinder disk. I have the tool with the two pronges that slide into the nut but the wheel keeps spinning. There must be a trick?


On the top of the grinder there should be a button. hold that in while turning the disk (please have the grinder unplugged while you do this).The button wil drop further in when it finds the notch in the gear. This will lock the spindle, allowing you to remove the retaining nut.
Read More At : 9015A 5" Electric Angle Grinders...

Hey there I do not know how this fix ya site works but I will give it a shot. I am stumped I am working on a nine inch grinder, and here is what it does. Hit the button and it will run for about six seconds then trip a 15 amp breaker. Here is what I checked, the brushes have plenty of life in them, I opened the case unplugged the switch from the motor and I checked it out and is working properly. Moving on to the motor, first I checked for any kind of binding and it is as free and spins well. I went deeper I pulled the entire rotator out of the case and took some emery cloth to it and made the copper armature shine, and cleaned out all the groves, then put it all back together again. I put the brushes back into the case and have 0.9 ohms between the brushes, everything looks well am I just not seeing something that I should....??? Oh yea while I had the brushes out I did check the resistance between the opposing coils on the stater and there is not a short. If for some reason you can think of something that I did not check please let me know. Thanks Tom.


Hello, W/D here.You've checked quite a bit! When you polished the armature contacts, did you polish along the length of the contacts? If not, re-polish in the long direction, and then clean the contact area with electrical cleaner. This may help.--W/D--
Read More At : BOS18946 9" Large Angle Grinder...

Makita grinder keeps tripping circut breaker - Makita Saws


FIRST OF ALL !! Control where the tool is used first for undervoltage on the mains supply group. If it is everywhere a problem FIRST replace the circuit breaker. After that control all connectors last check interference suppression capacitor. If all are controled , relace armature or electric field or both.
Read More At : Makita...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0351 seconds