Guide :Saws : 10", Table Saw with Stand, Powerful 2.6A Motor with Ste

Hitachi Table Saw Quit Working

I was ripping down a 4X4 with my 10" Hitachi table saw when it bogged down then stopped. Upon trying to restart the saw, it seemed to be seized up. There was some smoke coming from inside the casing right before it went down. I thought it was from the hot wood. A few minutes later I tried it again and it starts to turn very slowly then trips the breaker. It also pulls a lot of juice on the circuit (I see the lights dim). As of now it starts to rotate very slowly and makes a humming noise. It does so for approx. 12 revolutions, before it trips the breaker. I tried some WD40 on the wheel

Research, Knowledge and Information :


Table Saw motor not working after cleaning sawdust from it ...


So, I take the shop-vac and prop the table saw back off it’s stand (Hitachi work site saw c10fr,) undoing the bolts so I can mount it onto a shop made stand.
Read More At : lumberjocks.com...

My table saw motor just stopped.. What do I do?


I was ripping a bunch of boards into small strips and although the saw was working ... I did the same thing on my table saw ... My table saw motor just stopped.. What ...
Read More At : forum.woodenboat.com...

repair - Troubleshooting a circular saw that quit working ...


I have a circular saw that quit working for no obvious reason. I cut a board and sat the saw down to get another board. When I tried to cut the next board, the saw ...
Read More At : diy.stackexchange.com...

Hitachi Power Tool Parts | Great Selection | Great Prices ...


We have the genuine Hitachi parts and tool repair help you need to get your power tools running ... If you’re looking for a Hitachi model ... Table Saw Parts;
Read More At : www.ereplacementparts.com...

Hitachi C10FCE 10" Compound Miter Saw Parts


Need to fix your C10FCE 10" Compound Miter Saw? We have parts, diagrams, accessories and repair advice to make your tool repairs easy.
Read More At : www.ereplacementparts.com...

Hitachi Chain Saw - YouTube


Jul 13, 2010 · Hitachi Chain Saw teamtoolsonline. Loading ... This guy puts a finger into an active table saw blade & comes away ... Hitachi CS38EK chain saw ...

Electric Blade Brake | Fine Woodworking Knots


A quick question regarding Dewalt's Sliding Compound mitre saw, the electric blade brake on mine has stopped working. ... particularly dewalt and hitachi. Clampman ...
Read More At : forums.finewoodworking.com...

Suggested Questions And Answer :


Hitachi Table Saw Quit Working


Sounds like you've got problems with the armature commutator or one of the bearings is bad. Your best bet is to take it out and visit a local motor repair shop to asses the problem. A new motor could be the answer but at some heavy duty expense.
Read More At : 10", Table Saw with Stand, Powerful 2.6A Motor with Ste...

Hitachi c10fr table saw wiring diagram


Here is a hand drawn diagram Please rate this a fixya
Read More At : 10", Table Saw with Stand, Powerful 2.6A Motor with Ste...

Want to replace under powered saw motor on sears 10"table saw


U can put a 2 and above if u want just need to have the correct rpms
Read More At : 10" Table Saw...

Hi i need to rewire my ryobi table saw switch thanx lee


What I do is to take a photo of the wiring and effected area so I can refer to it when I get lost. Just replace each wire one at a time from the old switch to the new. Good luck
Read More At : 10", Table Saw with Stand, Powerful 2.6A Motor with Ste...

Bosch 4000 table saw won't work


OK sounds like you are handy. You have electric to the brush tubes? (first unplug saw to test) If yes then I would remove the brushes to see if they were making contact with the commutator. Does the blade spin freely? If not you might have a bearing problem. I would again use air after removing the brushes and then reinsert making sure they seat on the armature. If still nothing then if you are comfortable I would pull the motor housing. But before pulling go to Bosch Tools website and downloading a breakdown of your saw. Let me know if I can help
Read More At : 4000 - 07 Electric Table Saws...

My Powermatic Model 64A table saw is 10 years old and has been lightly used as a hobby. It's powered to run on 230 volts. Beginning two weeks ago, the motor has begun to shut down during use. Sometimes it will re-start and work fine for an entire day and other times it will not re-start at all. Must dust collector runs on the same electrical circuit without problem. The table saw problem occurs with and without the dust collector drawing power. Tim in Knoxville Does this sound like a bad switch, lose electrical connection or a motor problem? Or, could it be something really simple that I'm overlooking?


Does wiggling the cord cause the problem?
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

New table saw motor very weak and has problem kicking on


Is there an external phase shift capacitor for the motor? A defective phase shift capacitor can cause no or slow motor rotation and reduced motor power.
Read More At : Craftsman...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0786 seconds