Guide :Saws : RS20 13 Amp Reciprocating Saw

Blade stuck in the chuck

A blade broke off in the chuck and I can't get the piece out

Research, Knowledge and Information :


Ridgid reciprocating saw, unable to change blades - RIDGID ...


The blade chuck gets loaded with plaster and sawdust or tree resin and becomes jammed.
Read More At : www.ridgidforum.com...

How to Change the Blade Clamp on the Milwaukee Sawzall - YouTube


Feb 03, 2009 · How to Change the Blade Clamp on the Milwaukee ... How To Repair Quick Lock Blade Clamp on ... How to Replace Porter Cable "Recip" Saw Chuck ...

Chuck steak - Wikipedia


Chuck steak is a cut of beef and is part of the sub primal cut known as the chuck. ... under blade steak, shoulder steak and shoulder roast, ...
Read More At : en.wikipedia.org...

How to Remove a Stuck Drill Chuck - YouTube


Aug 11, 2010 · Remove stuck keyless drill chucks with this demonstration video's alternative repair techniques. Get a replacement chuck for your power drill here: http ...

How to Replace Porter Cable "Recip" Saw Chuck Pins ...


This article provides step by step instructions for replacing the chuck pins in Porter Cable reciprocating saws, a common power tool part replacement.
Read More At : www.ereplacementparts.com...

Issues w/ Recip Saw chuck - RIDGID Plumbing, Woodworking, and ...


When I'm using it I'll bear down on the nose to get the blade moving through the item being cut and the blade pops out. It gets stuck in ... Issues w/ Recip Saw chuck
Read More At : www.ridgidforum.com...

how to mend it .com - broken blade in reciprocating saw ...


broken blade in reciprocating saw? a saw blade broke and the end is stuck in the chuck and will not come out.....any way to release it? it's a Porter Cable PC85TRSO.
Read More At : howtomendit.com...

Suggested Questions And Answer :


Blade stuck in the chuck


If you have the lock released and can't get it out try pointing it towards the ground and running it. the piece should fall out unles it is still locked in
Read More At : RS20 13 Amp Reciprocating Saw...

I have a Bosch RS20 recip saw. A blade broke off in the chuck and I can't get it out. What should I do to get it out of there? Thanks for your help. Dan


Hi,Getting a broken blade our of the sawzall chuck can be difficult and require some ingenuity and patience...Sometimes there be enough blade left so that you can grab it with a needle nose pliers... othertimes it is flush and that makes it more difficult... holding the chuck in the release position and rapping the saw against a table or with a hammer can jiggle the piece out....of course you have the chuck pointed down while you do that...Also moving the piece around a bit with a stiff wire and also soaking the chuck and blade with WD-40 helps also....Usually it will take a combination of these things and some persistance to get the job done...heatman101
Read More At : RS20 13 Amp Reciprocating Saw...

The blade lever on my sawzall is stuck in the up position


Oohh, that a tough one. you gotta, very carefully peal back the hand gaurd, the rubber where you hold onto it, at. Then releas the screws undeneath. Seems like you should be able to cycle the saw to its furthest out position, then remove the blade gaurd, uning some pliers of some sort you should be able to make the release, release. Hope this helps
Read More At : 8.0 amp Reciprocating Saw...

Blade stuck in reciprocating saw


The pin is probably stuck in the blade. This happens from time to time after they get dirty. Take some WD-40 or some other type of penetrating oil and spray a little in the blade holder while working the release lever. It will probably free right up.
Read More At : 8.0 amp Reciprocating Saw...

My Bosch rs20 reciprocation saw at stuck open and is locked. I am unable to turn the locking mechanism. thanks for help


You have to press the blade into place to trigger it to close.
Read More At : RS20 13 Amp Reciprocating Saw...

Reciprocating saw-snapped blade-cannot be removed


What I would try is to spray some WD40 on the pin first and then see if you can find a small screwdriver or punch and try pushing the pin in further to release the broken blade. It doesn't sound as though it is anything major, maybe a burr on the side of the pin or possibly rust or debris. DON"T hit the pin because you might damage it or push it in and never get it back out. Looked at a diagram and it appears that they used roll pins to hold the clamp in place so it might be that one is cracked or mushroomed and you might have to drive them out. I suggest that you go to Searspartsdirect.com and type in your model number to look at the same diagram.
Read More At : 8.0 amp Reciprocating Saw...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0598 seconds