Guide :Saws : Saws

Trouble removing blade

Bolt securing blade is so tight - don't know if this is a left hand or right hand thread - don't want to strip the thread in the motor

Research, Knowledge and Information :


Trouble Removing Riding Lawnmower Blades


Hi all! I'm trying to remove the blades from the 42" cutting deck of a Troy-Bilt Pony. The current blades were the ones that came installed, about 3 years ago. I have ...
Read More At : www.lawnmowerforum.com...

problems removing the blade nut | Shop Your Way: Online ...


Get shopping advice from experts, friends and the community! I have a Craftsman Push Mower ,Sears Item# 07137034000 | Model# 37034. I am have problems removing the ...
Read More At : www.shopyourway.com...

having trouble removing bolt for lawnmower blade | EGO ...


having difficulty removing bolt to change blade have tried hammering the wrench and using lubricant - any suggestions!!!!
Read More At : community.egopowerplus.com...

Blades Major trouble removing blades - Page 2


I just bought a set of blades for my Cub Cadet Z-Force 44" and have run into problems removing the old blades. The three blades are each bolted on by a 1-1/8 nut. I ...
Read More At : www.lawnmowerforum.com...

Having trouble removing blades ( Homelite T-8 ) - Talking ...


I've busted my knuckles enough on my own trying to get these blades off. Maybe someone sees something I'm missing. I'm assuming these are NOT reverse...
Read More At : simpletractors.com...

Change a lawn mower blade safely and easily - The Silicon ...


To remove and replace a lawn mower blade safely and ... Lawn mower blade removal direction is another ... And if you have trouble starting your mower on a ...
Read More At : dfarq.homeip.net...

Newbie having trouble removing blade from Miter saw ...


Admittedly, I'm a beginner in woodworking or anything relating to carpentry. Experimenting, I exchanged a 8 1/4" blade with a 7 1/4" blade as it was the only one I ...
Read More At : www.woodworkingtalk.com...

Riding Lawn Mower Blade Replacement Instructions | MTD Parts


Riding Lawn Mower Blade Replacement Instructions. ... Remove the blade and blade ... Resolving outdoor power equipment problems as soon as they arise will prolong the ...
Read More At : www.mtdparts.com...

How to Loosen a Tight Bolt Holding the Blade on a ... - SF Gate


It's typically fairly simple to remove the bolt holding the blade in place on a Craftsman riding lawn mower -- unless, of course, that bolt is stuck. The blade on ...
Read More At : homeguides.sfgate.com...

Suggested Questions And Answer :


I am trying to remove a motor from my 10'' Bosch table saw. I am having trouble removing the pin on the side where the gear is that moves the blade up and down. I got the pin out on the other side easily. Can you help me?


They are both just slide into the aluminum frame. If you haven't done it already the easiest way to service the parts you are talking about is to remove the plastic housing so you can access the pins easier. Make sure you remove both the c-clips and to pin should slide out. Sometime there is saw dust in the pin bores and you have to use a small pin punch and hammer to tap the pin out.
Read More At : Bosch...

How to reinstall saw guard on Mac Allister MAC185LS?


Never heard of this brand of saw. A Google search indicates that MacAllister only makes big earth moving equipment. Otherwise, most saws have an appropriate washer and retaining clip that holds the guard on. And you'll need the original spring to return the guard to the closed position every time you use it. Then there are two shaped washers that fit on the armature that have a 5/8" shoulder to fit a normal saw blade. Finally there is the nut that holds everything on. Hope you didn't lose all these parts. If you did, go to eReplacementparts.com and and enter your make and model. If they don't have what you need you might be plum out of luck. But a new saw.
Read More At : Saws...

Reciprocating saw-snapped blade-cannot be removed


What I would try is to spray some WD40 on the pin first and then see if you can find a small screwdriver or punch and try pushing the pin in further to release the broken blade. It doesn't sound as though it is anything major, maybe a burr on the side of the pin or possibly rust or debris. DON"T hit the pin because you might damage it or push it in and never get it back out. Looked at a diagram and it appears that they used roll pins to hold the clamp in place so it might be that one is cracked or mushroomed and you might have to drive them out. I suggest that you go to Searspartsdirect.com and type in your model number to look at the same diagram.
Read More At : 8.0 amp Reciprocating Saw...

My saw problem has to do with changeing the blade. I'm useing a thin kirf blade. When I change the blade I have to put a wrench on the arbor next to the pulley to keep the arbor shaft from turning when I loosen the nut to remove the blade. I try to put a block of wood in the teeth of the blade to hold it while loosening the arbor nut with the wrench. The arbor nut turns with the arbor shaft and the blade doesn't move. I've used this blade for a few years without a problem. When I use my dadoe stack it does the same thing. The arbor shaft turns with the arbor nut when trying to loosen the nut to remove the stack. Any suggestions on what to do or whats happening?


The nut is binding on the arbor because the threads are buggered up or clogged with something. It could be the nut (which is probably brass and soft) or the arbor (which is steel). If it got a little cross threaded, the damage will be on the nut. It might be the arbor if the arbor took a whack. Once you have it apart you should be able to see it - although the damage might be pretty small. You aren't likely to have a tap and die to run through the threads, but you can probably fix it with a little rotary tool (like a dremel) using a small disc. If it is the arbor you can use a triangular file. Or you can buy a new nut. I hope this helps.
Read More At : 10" Table Saw...

Cant get blade off


I don't know which model you're using, but normally there's an arbor lock button on the motor side of the blade somewhere that allows you to lock that whole middle housing down so it won't turn. Look underneath the motor and see if you can't find some kind of lock botton or lever. That will make it easy to loosen the nut and tighten the blade down correctly.Otherwise you're going to have to improvise some way to lock it in place enough to break that nut loose.Reply with a model # and I can try to find a parts schematic to check for you...
Read More At : Saws...

How do I remove the rubber covering from the lower housing on craftsman 172.171800 recipricating saw?


James, you answered your own question. Remove the foot. The pull the pivot pin from the blade release mechanism. The lever will move to the inside of the housing. The spring is in a slot that is open-ended; you can push the spring out. Then remove the lever w/spring. The cover slides off, but not easily.
Read More At : Saws...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0763 seconds