Guide :Saws : 10" Dual Slide Compound Miter Saw with Light LS1013F

45 degree cut

Hello!I lost my manual and I need to adjust my 45 degree cut on my Makita. How do I do that?Thank you.

Research, Knowledge and Information :


How to Cut 45 Degree Angle Baseboards With a Hand Saw | Home ...


When you're installing baseboards, the quality of the cuts makes the difference between an expert job and a so-so one. Although it isn't difficult to make accurate 45 ...
Read More At : homeguides.sfgate.com...

Quick Tip #1: Cut the Perfect 45 Degree Angle - YouTube


Jun 06, 2014 · Visit http://www.meadmclean.com for blogs, resources, and other news. A quick tip for framing or building stretcher bars. Use a speed square to line up the ...

The 45 degree cut - YouTube


Feb 10, 2009 · Here is how to make a 45 degree cut using the slide tray and the Revolution XT by Gemini Saw. Always use the magnetic brackets.

45 degree cut | eBay


Find great deals on eBay for 45 degree cut. Shop with confidence.

How do you cut wood at a 45 degree angle? | Reference.com


Perhaps the simplest way to make a 45 degree cut in a piece of wood is by using a miter saw, but a circular saw and a speed square can also make precise cuts. Miter ...
Read More At : www.reference.com...

Circular Saw 101: How to Make an Angle Cut | This Old House


Circular Saw 101: How to Make an Angle Cut. ... Learn to set the lever for a 45-degree angle or to correctly match an angle for any other unique measurement.
Read More At : www.thisoldhouse.com...

45 Degree Cutter | eBay


Find great deals on eBay for 45 Degree Cutter in Metalworking End Mills. Shop with confidence.

0, 45, 90, 180 Degree Haircuts aka Layered Hair - Pinterest


Modern Hairstyles with Bangs – Haircuts and hairstyles for 2017 hair colors trends for long short and medium hair. Find this Pin and more on 0, 45, 90, 180 Degree ...
Read More At : www.pinterest.com...

How to Miter Corners: 13 Steps (with Pictures) - wikiHow


How to Miter Corners. ... The most common miter angle is 45 degrees. ... How to cut boards in a 90 degree without a miter box?
Read More At : www.wikihow.com...

How to Use a Miter Saw - Lowe's


How to Use a Miter Saw. ... Most saws cut from 90 to 45 degrees in both directions, and some saws can cut up to 55-degree angles.
Read More At : www.lowes.com...

Suggested Questions And Answer :


How to adjust saw to cut a perfect 90 degree and 45 degree cut


I would go to Makitausa.com and download a manual. what you have aproblem with is either a bent fence or just misalignment. simply all you need is a good square, put the head at 0 degree and check to see if out, making sure not to put square on the teeth of the blade, if it is out there are 4 13mm bolts that hold fence in place loosen them and starting from the left side put it at the exact dead nut. snug the bolt and then check the right side. I usually check them 3 times for accuracy when you are confident snug all the bolts and recheck. Let me know if you need more assistance
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

45 degree cut


Are you having problems with the miter or bevel ? Are you asking how to physically move the saw to that degree angle?
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

Frozen slide mechanism


Lubricate it with graphite powder OR silicone spray lube but not both
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

Makita miter saw has no power - Makita 10" Dual Slide Compound Miter Saw with Light LS1013F


Disconnect it from the wall outlet. Use a VOM set to continuity (i.e ohms) connect one lead to each of the power cords. Depress the start switch. If switch and circuits are good you should get either a low reading or just 0.0. IF you get no reading or really high reading the unit has an internal fault and more troubleshooting will have to be done.
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

Recalibrating the angles - Makita 10" Dual Slide Compound Miter Saw with Light LS1013F


Look on top of fencesee 4 holes loosen 4 bolts (probably hex wrench) and fence will loosen alsoframing square against loose fence and lowered blade (to calibrate square)tighten fence,... square to blade
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

The blade guard will not retract when saw is moved down to cut stock. Small bolt with washer and bushing fell out.......how do I repair this with out taking to a shop. Item LS1013FL


Find a small bolt and bushing...any home improvement store will have one..until you put the bolt and bushing back the blade guard won't work..this happens all the time and guy's i work with just go find a store with the same saw and grab the bolt and bushing from the floor model and take it to the counter..they will only charge you a few cents for it.
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

Makita LS1013 compound saw wont slide,instruction manual no help. I have nevr operated a miter saw before so any help would be appreciated


You may find, you have a lock, button, that needs to be held in, before you can drop the saw to cut.
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

It doesn't give me a precise 45 degree cut


The fence might be bent or needs to be squared up. how is the 0 degree. If you need to find out how to square this tool go to Makitatool.com and type in your model number and you can download a user manual with the instructions on how to do this, let me know I work on them every day. Good luck
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

Promblem with Makita 1013 ajusting blade to cut square


Just found your problem, what you need to do it unplug tool and get a good square. Set the blade at 0deg. and then put the square on the left side of the blade to check it. If it is out of square you would need to loosen the fence bolts (13MM) and adjust the fence, snug bolts on the left side and move your square to the right and recheck and then snug the bolts there, I always recheck the fence to ensure it is square and not moved before tightening the bolts fully. If the head is out there are bolts on the pivot that need to be adjusted and again recheck. If you go to Makitausa.com you can download an owners manual with instructions on what to do. Let me know if you still have problems.
Read More At : 10" Dual Slide Compound Miter Saw with Light LS1013F...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1041 seconds