Guide :Saws : 7 - 1/4" Skilsaw Circular Saw

My bosh 1677m is less than one years use and it started sparking toward the motor and stopped working. It is not the power cord. what else could be the problem??? thank you

Posted by dperry3434 on Dec 06, 2008

Research, Knowledge and Information :

LeBron James Releases Finals Frustration On Poor ... - Deadspin

Do you not recognize the “It’s my ... The one thing that ... and other reports have made the case that their efforts might be working, but they’ve still not ...
Read More At : : The Guru's Den Archives - First Week of 2005

... in that it lasted less than 100 years. Would you ... Ford Motor Company had a serious problem for a ... if more than one person is going to working ...
Read More At :

Bulletin Daily Paper 02-16-14 by Western ... - issuu

The Bulletin Daily print edition for ... Less than I mile from city ... "He and I over the years started to develop a better working relationship ...
Read More At :

Cleveland Cavaliers To Part Ways With General ... - Deadspin

With the team at the center of trade rumors—not to mention three days before the draft—the Cavaliers have decided to part ways with general manager David Griffin.
Read More At :

Ignore Elon Musk and Mark Zuckerberg's War Over Killer Robots ...

“I think that job displacement is a huge problem, and the one that I wish we could ... who are working on new AI products that ... this warning for years.
Read More At :

2 via Cartão Leader - 2 via do boleto e cartão por e-mail

That’s it and nothing else. There is no less ... bank could hold at any one time to no more than 5 ... for the motor fuelin the next five years, ...
Read More At :

slightly less than $3 million. hit $33.693,557, ... you started for ... bought the new building.One Keegan working on their Troop
Read More At :

9-25-14 Edition | Caltrain | Cannabis (Drug) -

... 9-25-14 Edition. View More. 9-25-14 Edition. ... road to the public less than two years later. ... throw at a problem, you’re going to be held
Read More At :

Suggested Questions And Answer :

My bosh 1677m is less than one years use and it started sparking toward the motor and stopped working. It is not the power cord. what else could be the problem??? thank you

It might need the brushing replaced, sometimes just adjusting them works, or cleaning them. You could also look at all the solder joints to insure that they are in tact. I've found that the switch is the week point in a lot power tools. You can check the switch by using a multi-meter and ohming it out. With the meter set to the Ohms setting you should read zero Ohms with the switch set to on and a really high number if not a bunch of flashing 8's depending on the meter when set to off.
Read More At : 7 - 1/4" Skilsaw Circular Saw...

New table saw motor very weak and has problem kicking on

Is there an external phase shift capacitor for the motor? A defective phase shift capacitor can cause no or slow motor rotation and reduced motor power.
Read More At : Craftsman...

Blown engine I have ten saws i rent out, and have had four motors blow in the past month. the saws are getting old, but are well maintained. When I rent them out, i send them with a can of premixed fuel, so the customer does not put regular gas in the machine. The premix is 50:1 using 2 cycle engine oil from Stens. My question is, Is there a better oil to be mixing with these older saws? Or is there anything else that could be scaring the piston and cylinder, and blowing the motors? (compression is @ 75psi)

Makita likes you to use at least 91 octane fuel and a synthetic oil mixture. the stens oils is garbage, i switched to the makita oil around 6 months ago and i havent had a problem. also, the wacker saws use the same motor and their piston heads are sleeved in carbon so they last longer and dont score the cylinder as fast as the stock makita heads. makita also makes a 100:1 mix hi performance oil you can use.
Read More At : DPC8112 16" 81CC Gas Powered Power Cutter Circular Saw...

I have no power to saw. I have checked the switch and still no power. Is it possible that the power cord could be bad? Is there something else I should try?

If you have a volt/ohms meter remove the handle half to expose the wiring and unplug tool test the cord by itself and if ok continue on thru the brush holders.
Read More At : DW715 Heavy Duty 12" Single - Bevel Compound Miter Saw...

Where do you wire power cord on skil circular saw 5400 to switch

Very easy to tell the short wires go to the cord side. The longer ones go to the motor. The wire will be same color as the cord wires. They will come from the back of the switch as it sets in saw.
Read More At : 5400-01 7-1/4-in Skilsaw...

I have a makita 5997nb circular saw that i have had for 26 years with no problems. but now it will not power up. I think its the cord. How do I replace it myself?

The cord ... or the switch ... or the brushes. You will have to take the handle apart to access the end of the cord and check the switch. Test your cord with the ohm function of a volt/ohm meter. Thanks for your question and good luck with your repair.
Read More At : 7 1/4" Circular Saw 5007NB...

I sawed the power cord in half...! It was a skil saw brand But obviously I am 'unskilled'... The saw cost about $65. Can this be repaired or should I get a new saw...?

Yes it can be repaird. No offense, but can you do it? Take handle appart, may have torx screws, and remove old cord. You can buy a new exact replacement cord or a generic cordset to replace. Check wire size on your old cord.
Read More At : 7 - 1/4" Skilsaw Circular Saw...

Bosch Miter Saw Turned On By Itself

A ghost in the machine? That sounds like a good one for Bosch tech support. I've never heard of any saw doing that, and I bet they'd be interested to know about it... All I can imagine is a short in the switch, some kind of power surge you weren't aware of, or a practical joke. At any rate: Contact Bosch:
Read More At : 12" Compound Miter Saw 3912...

I purchased a demo model of the RotoZip 10 from my local Lowes store. The cord had been cut off the tool. I replaced the cord and my tester shows that I have power running to the tool. The tool does not turn on. Could the problem now be the switch?

Hi, W/D here.Check the brushes first. Demo's get pilfered for small items, and the brushes may have been 'misplaced'. If they're there, then trace your wiring through the switch.Best regards, --W/D--
Read More At : RotoZip Spiral Saw RZ10 - 2100...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0742 seconds