Guide :Saws : Circular Saw W/Dual Laser

Motor won't shut off unless unplugged

Whenever I plug in the saw, the motor starts up automatically. Is there a short in it or anything? The only way to shut it off is by unplugging the saw.

Research, Knowledge and Information :


Chevrolet Corvette Questions - Cooling Fan Problem - CarGurus


Cooling Fan Problem - Our electric engine cooling fan comes on at cold start up and won't shut off unless I unplug the relay. The wiring gets very hot at t...
Read More At : www.cargurus.com...

how to mend it .com - Washer won't shut off unless unplugged ...


Washer won't shut off unless unplugged? My maytag bravos washer will not shut off when i press cancel. The lights go out but the motor is still going.
Read More At : howtomendit.com...

Key won't turn car off unless alternator is unplugged - Old ...


... Key wont turn car off unless alternator is unplugged ... car won't turn off with key. Alternator unplugged: ... Then off with engine running?
Read More At : www.ultimatesubaru.org...

The blower wont turn off unless unplugged. Its a Carrier


The blower wont turn off unless unplugged. Its a Carrier - Answered by a verified HVAC Technician
Read More At : www.justanswer.com...

How To Fix Dryer That Won't Shut Off | Dryer Repair


Repairing a dryer that won't shut off many seem ... with when the dryer is unplugged ... dryer the timer consists of a small motor connected to a series of ...
Read More At : www.partselect.com...

Motor won't shut off???? Page: 1 - iboats Boating Forums | 283030


Please do not post to topics that have been inactive for more than 3 months unless you ... Motor won't shut off ... and the motor still ran....then I unplugged the ...
Read More At : forums.iboats.com...

Compound Miter Saw Wont Shut Off - DIYChatroom


Compound miter saw wont shut off. ... all out in that area with an air hose while working the trigger on and off. (unplugged, ... saying cleaning it won't work, ...
Read More At : www.diychatroom.com...

MD QandA for TroubleShooting Power Unit Issues


TroubleShooting Power Unit Issues Q&A. ... the unit would not turn off unless unplugged. ... an old motor may cause it to shut off and then it may start back up by ...
Read More At : builtinvacuum.com...

Indoor fan won't shut off unless I use the circuit breaker ...


Commonly Reported HVAC Problems. ... Indoor fan won't shut off unless I use the circuit breaker: ... it really doesn't hurt the motor or cost more money, ...
Read More At : www.hannabery.com...

Suggested Questions And Answer :


Motor won't shut off unless unplugged


Bad trigger switch period
Read More At : Circular Saw W/Dual Laser...

Compound mitre saw won't shut off unlss unplugged


Check yhe switch it may have dirt in it or be bad. But the switch is the first place to check.
Read More At : Circular Saw W/Dual Laser...

Power Glide Circular Saw with Laser Guard Spring Broken


The spring hooks onto the blade guard and wraps around the hub of the blade guard. It is orta hard to see but it will hook onto the guard.
Read More At : Power Glide Circular Saw with Laser...

I have a Powermatic III Model 66 table saw with a 5 HP motor. Saw motor will not start unless I remove Switch Box cover and hold down the on switch. As soon as I let off the switch it comes back out and the saw shuts down. That is to say, the switch cannot hold itself in, at the on position. I'm wondering if the entire switch assembly has to be replaced or if it is repairable without a lot of work and trouble and buying a lot of various parts? Thank you


Replace the entire switch assembly, otherwise you will be doing a lot of work and buying individual parts that very well won't be available.
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

Have a craftsman 10 inch table saw model #137.218250, serial #RCW3145. When we attempt to cut plywood or a 2X4 length ways, the motor dies a number of times. Most of the time the reset button will not work unless we first unplug the electric. It will cut a short distance then die. This is with a very slow feed. We used an older table saw and it worked fine so know our feed is not the problem. Do you know the answer to the situation?


Sounds like the reset button needs replaced. Also when is the last time you cleaned the motor area?? When you reset the button is the motor "hot" to the touch and if so could also be a motor problem,, try the reset first
Read More At : Saws...

The saw wont cut all the way through the wood. Why?


First off what is the blade diameter and the wood thickness?? Also do you have the table adjusted for the maximum depth, It is one of the 3 items mentioned.
Read More At : Power Glide Circular Saw with Laser...

Circular saw motor turns when tightening saw blade


Insert a tool such as a screwdriver across the blade guard and against a tooth to prevent blade rotation, then tighten the blade nut. Be sure to remove the wedging device before operating the saw
Read More At : #Fury 7 1/4" Mp Circular Saw...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0767 seconds