Guide :Saws : Variable Speed Quik Change Tiger Saw Kit 9746

The motor from my reciprocating saw started emitting smoke.

I took the saw apart and found a small black piece of plastic, roughly the size of a quarter but couldn't find where it came from. I cleaned the inside a little and put it back together but it just started smoking again. It seemed to have lost some power as well. The brushes looked fine to me.

Research, Knowledge and Information :


Light Emitting Design LED-8032M57-A - Crescent Electric ...


Shop Light Emitting Design LED-8032M57-A at Crescent Electric Supply ... Reciprocating Saw Blades; ... Light Emitting Design Catalog#
Read More At : www.cesco.com...

Light Emitting LED-8025E30 - cesco.com


We respect your privacy. Specify email and we will send the answer to your address. We never reveal your information or use it to send you not related email.
Read More At : www.cesco.com...

New products for December 6, 2012 | ModelRailroader.com


New products for December 6, 2012; New products for December 6, ... driver-synchronized puffing smoke unit, ... Sawmill with micro-motion reciprocating saw.
Read More At : mrr.trains.com...

Explore Saw Tool, Reciprocating Saw, and more! - pinterest.com


The Portable Power Supply – Don’t get Caught in the Dark » Coolest Gadgets -Check out Brookstone’s Portable Power Supply, providing up to seven hours of power ...
Read More At : www.pinterest.com...

Air conditioner Noise Diagnosis & Cure: How to Evaluate Air ...


Buzzing noises at the outside fan motor: ... element if the equipment is started-up before ... compressor motor may (if the motor is a reciprocating ...
Read More At : www.inspectapedia.com...

Explore Dewalt Tools, Stanley Tools and more! - Pinterest


Discover (and save) your own Pins on Pinterest ... for this reciprocating saw. The variable-speed motor ... bill shows the dust and smoke.One ...
Read More At : nz.pinterest.com...

Milwaukee Power Tools & Accessories - Pinterest


Find this Pin and more on Milwaukee Power Tools & Accessories. ... driver Sawzall reciprocating saw ... I started a new series, Power Tools 101 with my buddy ...
Read More At : www.pinterest.com...

DeWALT Cordless Drill Gearbox - dwtoolparts.com


DeWALT Cordless Drill: ... Reciprocating saw is equipped with a keyless blade that makes ... ... Dewalt 18 volt cordless XRP drill emitting smoke, ...
Read More At : www.dwtoolparts.com...

Suggested Questions And Answer :


The motor from my reciprocating saw started emitting smoke.


That small black piece, was it somewhat flat? I am thinking that it could be part of the fan or baffle. As far as the smoking when you had it apart how did the windings look on the armature and field? It is possible that this piece of plastic opened up the windings and there is a short in the electrical components. If that is the case I would suggest taking to a repair center to get is looked at. Let me know what you find
Read More At : Variable Speed Quik Change Tiger Saw Kit 9746...

How do you remove the fan from the armiture? - Porter Cable Variable Speed Quik Change Tiger Saw Kit 9746


Generally they are pressed on. make sure that you can buy a replacement fan, sometimes they are not available. Give me the brand and model number and I will check it out for you.
Read More At : Variable Speed Quik Change Tiger Saw Kit 9746...

Variable speed quit working


You would need to replace the switch, give me a model number and a location with zip code and I will try and find one locally for you, Its not that hard
Read More At : Variable Speed Quik Change Tiger Saw Kit 9746...

Replacing shaft on tiger saw


If the spindle is broken you have to take the front of the saw apart, but check for excessive wear in the other parts before buying just the one. Its not that hard just pay attention when you disassemble
Read More At : Variable Speed Quik Change Tiger Saw Kit 9746...

Cannot get the blade out of the porter cable reciprocating saw


Hi,Getting a broken blade our of the sawzall chuck can be difficult and require some ingenuity and patience...Sometimes there be enough blade left so that you can grab it with a needle nose pliers... othertimes it is flush and that makes it more difficult... holding the chuck in the release position and rapping the saw against a table or with a hammer can jiggle the piece out....of course you have the chuck pointed down while you do that...Also moving the piece around a bit with a stiff wire and also soaking the chuck and blade with WD-40 helps also....Usually it will take a combination of these things and some persistance to get the job done...heatman101
Read More At : Variable Speed Quik Change Tiger Saw Kit 9746...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0778 seconds