Guide :Saws : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"...

Need a rocker switch for a Powermatic 63 A Artisan table saw part number 6285322

Posted by rlasita on Jan 03, 2009

Research, Knowledge and Information :


Powermatic 63 (0460174) 10" Artisan's Saw Parts


Need to fix your 63 (0460174) 10" Artisan's Saw? ... Part Number: 6285322. Not Available for Retail Sale. ... Powermatic 63 Table Saw ...
Read More At : www.ereplacementparts.com...

Table Saw Switch Help | Fine Woodworking Knots


Need some help on replacing this rocker switch from my Powermatic 63A Artisan 10" table saw. It is part number 6285322 in the parts manual. I bought this saw in 1989 ...
Read More At : forums.finewoodworking.com...

Suggested Questions And Answer :


Need a rocker switch for a Powermatic 63 A Artisan table saw part number 6285322


If you want to buy a new one, the Grizzly G1022 Table saw is an exact replica of the PM#63. A owners manual and parts list is available at their website. Grizzly.com
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

Aline table to blade - Powermatic 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30" Accu Fence System


Align blade and fence to mitre slot.
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

How do you set tension on overlocker - Powermatic 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30" Accu Fence System


I have no idea what an overlocker is. Help me out.
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

I have a Powermatic III Model 66 table saw with a 5 HP motor. Saw motor will not start unless I remove Switch Box cover and hold down the on switch. As soon as I let off the switch it comes back out and the saw shuts down. That is to say, the switch cannot hold itself in, at the on position. I'm wondering if the entire switch assembly has to be replaced or if it is repairable without a lot of work and trouble and buying a lot of various parts? Thank you


Replace the entire switch assembly, otherwise you will be doing a lot of work and buying individual parts that very well won't be available.
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

My Powermatic Model 64A table saw is 10 years old and has been lightly used as a hobby. It's powered to run on 230 volts. Beginning two weeks ago, the motor has begun to shut down during use. Sometimes it will re-start and work fine for an entire day and other times it will not re-start at all. Must dust collector runs on the same electrical circuit without problem. The table saw problem occurs with and without the dust collector drawing power. Tim in Knoxville Does this sound like a bad switch, lose electrical connection or a motor problem? Or, could it be something really simple that I'm overlooking?


Does wiggling the cord cause the problem?
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

How do I repair the tilt on my artisan table saw ?


I'm not familiar with your saw, but I'm familiar with table saws in general. The tilting is achieved by a worm screw on the end of the crank handle engaging a partial worm gear on the tilt mechanism. If all you get is clicking, the worm is jumping out of the teeth on the worm gear. It's likely that the shaft you're turning has slid a bit in its bearing and the far end of the worm is no longer constrained and no longer holds the worm tightly against the worm gear. I'd say just take the whole thing apart and re-assemble it. In the process, you'll find out how the worm has slipped out of place and you'll see how to put it back where it belongs so that the worm is supported on both ends.
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

I'm thinking of purchasing a Craftsman Model 113.29901 (circa 1970) table saw in good condition from an older carpenter that used it for cabinet work. It has 4 - 10" ext'ns with it. It has a little surface rust on the table. What would be a reasonable price for one? Anything I should look for? I just plan on using it for small projects around the house. Deck building, etc.


I can't tell you what the value is but I can share a tip I use whenever buying a used saw. With the saw in the 90 degree position (Straight up) run a board all the way through the board. Then flip one half of the board upside down and place the two cuts together. If the blade is true the two halves should line up perfectly. If they don't that means the blade is out of square. While re squaring a saw is fairly easy, I would wonder why the blade was off and how often that would happen and therefore would likely not buy the saw. Of a side note, Craftsman does make a great saw and they are fairly easy to work on and find parts for. Good Luck
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

I have an older Rockwell 10 in. table saw, model 34-440. The blade is cutting approx 2/32 to 3/32 off from front to rear causing a wide saw cerf and difficulty feeding the material through against the fence. What is the proper way to adjust the blade to run true?


These lightweight saws can be somewhat problematic in this respect. They have a tendency to come out of adjustment as they are moved about.First, make sure the blade you're using is true and has little runout. You can check this using a micrometer, or simply marking a tooth and spinning the blade by hand (power unplugged) to see if the blade runs true or wavers in its path. If the blade is warped or bent the problem is probably there rather than the table.Second, check to make sure the fence is properly adjusted, parallel to the mitre slots. If the fence is out of adjustment, the path of the material relative to the blade will not be parallel, and this can cause poor cuts.Third, hope it's one of the first two. If not, set a day or weekend aside to work on the saw. Get some good light and flip it over on a table or horses so you can see what you're doing. Have the parts diagram and owner's manual on hand.You'll need to loosen the bolts that hold the table top against the saw mechanism beneath the top, and shift the saw relative to the top in the desired direction to correct for the out-of true path of the blade relative to the table top. On some lighter saws like yours, this entails re-adjusting most of the saw mechanisms to run true, as they are frequently independently bolted to the underside of the table and not unified construction that moves as a single piece.You have to shift the saw slightly in the required direction, check the runout of the blade, then repeat until you get it right. If you're skilled and you don't mind standing on your head, you can do this with the saw in position.There are many excellent articles online that detail this procedure if you search google for "table saw tune up", so I won't elaborate on the details. Try to find one that has a saw similar to yours as an example. Good luck.I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread. If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

I have a Powermatic model 66 table saw that hums (at the starter switch not motor ) when I turn it on. I just rewired after moving but have checked all connectors with multimeter and I think it is wired correctly. Saw started fine prior to the move.


I am thinking that you have mistakenly crossed 2 or more wires, hopefully you wrote yourself a wiring diagram or there is one inside the motor cover. I don't know if I can find a wiring schematic for this tool. If you still have the owners manual look in there for initial setup and see if they provided one. If you need more help let me know and I will do what I can.
Read More At : 1660802K Model 66 Special Edition 10 Inch Left Tilt 3......

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0698 seconds