Guide :Saws : Saws

Which table saw

This is not a tech questions but an advice from expert . I am a first time table saw buyer and have done an extensive research and for my needs i have narrow down to two choices. steel city mod 35675 3 hp 30" or grizzly G1023SL 3 hp 30". can you give me some input on these models your input will be much appreciated then the ads thank you

Research, Knowledge and Information :


Best Table Saw - Reviews - 2017 - ConsumerSearch.com


Which are the Best Table Saws? Editors recommend portable, contractor and cabinet saws based on an analysis of expert and user reviews.
Read More At : www.consumersearch.com...

Portable Table Saw Reviews, Tests, and Comparisons


Jul 24, 2017 · The table saw is the beating, buzzing heart of the wood shop. The new breed of saws are not only tougher and more accurate than older models, but also ...
Read More At : www.popularmechanics.com...

Table Saws | Bench Saws - Sears


Sears has table saws for easily slicing through project materials. Customize the length and width of your project materials with a new bench saw.
Read More At : www.sears.com...

Choosing a Table Saw for Your Shop | Rockler Skill Builders


A table saw is one of the best investments a woodworker can make. Learn more about the different types of table saws before making your purchase.
Read More At : www.rockler.com...

Table Saw Buying Guide - Lowe's


Learn the basics of table saw capabilities and find out which features to look for.
Read More At : www.lowes.com...

What Table Saw Should I Buy? - The Wood Whisperer


Some things to consider when buying a new table saw.
Read More At : www.thewoodwhisperer.com...

Table Saws | Portable Table Saws | DEWALT


DEWALT's table saws make short work of any wood pile. DEWALT portable table saws are the perfect addition to any jobsite because they're Guaranteed Tough®.
Read More At : www.dewalt.com...

How to Buy a Table Saw - The Spruce


What features should you look for when buying a table saw? What are features that you don't need, to save some money? Here are table saw buying tips.
Read More At : www.thespruce.com...

Suggested Questions And Answer :


My very old Craftsman 10" Table Saw does not power on. While rip cutting some plywood, I errored and caused the blade to bind. Before I was able to power off the saw, the motor stopped. I thought I had popped a circuit breaker, but did not. Power to the table saw was still hot, yet when I power on the table saw it does nothing -- it's dead. The RESET button also does nothing. Does this sound like a broken switch or the motor? Craftsman 10" Table Saw - Model #113.295752 Please advise how to fit or whether to get a new table saw.


Go to searspartsdirect.com and put in your model number. Look at the motor and wiring section. Look at item 16. The motor overload protector. (probably your reset button) WIth saw unplugged, unwire one sid of this switch and test with an ohm meter. You should read through the switch. If it is open then that's why the saw doesn't work. Many of this type of oveload requires quite a push to reset as you're flexing a klixon disc back to make contact. If is open and you can't reset, it's available there although a bit high priced.
Read More At : 10" Table Saw...

I have a craftsman table saw model 113.27870. I need a table insert for a dado blade. I looked on the sears website and it said parts for this saw are no longer available. Will a table insert for a newer model craftsman table saw work or could I adapt one to work on this saw?


I would use mdf to create another throat plate and then slowly bring up the dado to create a zero clearance...throat plate will need to be held down while you come up with the dados..
Read More At : 10" Table Saw...

Want to replace under powered saw motor on sears 10"table saw


U can put a 2 and above if u want just need to have the correct rpms
Read More At : 10" Table Saw...

Craftsman model 708100 table saw tilt lock won't stay locked


Try removing the lock knob and putting a toothed lockwasher on the shaft. reinstall the knob.
Read More At : 10" Table Saw...

Delta table saw, 34-670, keeps shutting down


There could be several problems. First, make sure you have a sharp blade. Then check the arbor for drag just after you have been using it. Unplug it, lift the motor a bit (to loosen the drive belt) and turn the blade with your hand - it should turn very freely. Check the motor shaft for drag too by turning the motor pulley with your hand (with the belt loose). The motor should have just a tiny bit more drag than the arbor shaft. If all of these check out ok, then you might have an insufficient gage of wire between the electric panel and the saw - a thin wire long extension cord is often a problem. If you are using an extension, try to eliminating it and plugging directly into the wall. (It depends on the length, but in general don't use a cord lighter than 14 ga - higher numbers mean skinnier wire). And it could be that the house wire is too light - a long run of 14 gage wire is too light - you want 12 gage wire and a 20 Amp rated outlet. If all of these are not the problem, then you have a bad motor that is partially burned out (that is, the insulation on the coil windings has melted and the coil wires are shorting out resulting in coils with a lot less turns than the motor was designed for. You can replace the motor or get it re-wound. Good luck!
Read More At : Table Saw...

Table Saw Blade Won't Cut Straight


Inside the saw, on the end of the trunnion is a stop that is adjustable to zero the saw in to exactly 90 degrees. Either there is sawdust or something accumulated there or it needs to be adjusted. You say you cleaned it out, So you'll need to unplug it an have a look up in there. See how there's a geared piece of steel that moves when you crank the saw over to 45 degrees. Usually there's a bolt or stud with a locking nut on it, either on the trunnion itself or the lower surface of the table top. You need to break the nut loose and screw the bolt in or out to adjust, then crank the saw over to hit it, check for square with a known square, crank it all the way out of the way and readjust, etc. Until you get it right. Make sure to tighten that lock nut when you're done. I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread. If I've managed to answer your question or solve a problem, please take a moment to kindly rate this post....thanks!
Read More At : 10" Table Saw...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0869 seconds