Guide :Saws : Saws

I was using my Delta TS220LS table saw and it stopped running.

The motor will not even hum. The motor was not hot. I was only using it for about 1 minute before it quit. The blade does turn by hand and it has just slight resistance.

Research, Knowledge and Information :


DELTA TABLE SAW Parts | Model TS220LS | Sears PartsDirect


Shop for DELTA TABLE SAW repair parts for model TS220LS at Sears PartsDirect. ... to ensure proper fit and to keep appliances running for years to come.
Read More At : www.searspartsdirect.com...

My table saw motor just stopped.. What do I do?


The thing just stopped running. ... I don't know why, but it works on my table saw everytime. 04-06-2013, ... My table saw motor just stopped..
Read More At : forum.woodenboat.com...

Delta Power Equipment Corporation - FAQ Search Results


FAQ Search Results. ... like to purchase the Delta t-square fence system to use on my older Delta table saw. ... Switch the table saw ON. 7. With the saw running, ...
Read More At : www.deltamachinery.com...

Delta TS200LS Shopmaster 10" Portable Bench Saw with Legs ...


Delta TS200LS Shopmaster 10" Portable Bench ... This benchtop saw from Delta's Shopmaster line offers ... and a T-slot groove in the table so you can use a standard ...
Read More At : www.gosale.com...

Delta Table Saw problem | Fine Woodworking Knots


Delta Table Saw problem ... Got a bit of a problem here with my Delta 10" Table Saw. ... Funny thing was I noticed the saw stopped at the end of the cut.
Read More At : forums.finewoodworking.com...

Delta 34-670 table saw went dead, need advice - by Lloyd ...


I was cutting some 2 inch thick purpleheart with my table saw and all of a sudden it went dead. ... Delta 34-670 table saw went dead, need advice
Read More At : lumberjocks.com...

Is Your Table Saw Motor Stopping, Stinking, Smoking or Silent?


Is Your Table Saw Motor Stopping, Stinking, Smoking or ... or it could create unusual sounds when the motor is running. Since table saws naturally ... My table saw ...
Read More At : www.toolerant.com...

10 Table Saw - media.ptg-online.com


10" Table Saw (Model TS220LS) ... Delta may cause damage to the machine or injury to the ... on the table/work area when the machine is running. 20.
Read More At : media.ptg-online.com...

Suggested Questions And Answer :


I have an old delta tablesaw. It has a start and stop button. When the start button is pushed it used to start and run - now it only runs while the button is pushed. What is the problem? and how do I fix it?


Sounds like the on/off switch is bad. replace the switch with a switch that is of the proper voltage and rating value. a good place to find a switch is at your local hardware/industrial tool store. ( also try and find a switch at a industrial tool repair shop ). c...
Read More At : 1720305K 14" 7.5 HP 3 PH Model PM3000 Table Saw...

I was using my Delta TS220LS table saw and it stopped running.


I can solve your problem. I need a Delta TS220LS for parts and I do not care if it runs or not. I will buy the saw and you can buy a replacement. What do you say? Wayne Hill Anderson, SC 800 944.9577 864 356.3070 cell
Read More At : Saws...

Delta table saw, 34-670, keeps shutting down


There could be several problems. First, make sure you have a sharp blade. Then check the arbor for drag just after you have been using it. Unplug it, lift the motor a bit (to loosen the drive belt) and turn the blade with your hand - it should turn very freely. Check the motor shaft for drag too by turning the motor pulley with your hand (with the belt loose). The motor should have just a tiny bit more drag than the arbor shaft. If all of these check out ok, then you might have an insufficient gage of wire between the electric panel and the saw - a thin wire long extension cord is often a problem. If you are using an extension, try to eliminating it and plugging directly into the wall. (It depends on the length, but in general don't use a cord lighter than 14 ga - higher numbers mean skinnier wire). And it could be that the house wire is too light - a long run of 14 gage wire is too light - you want 12 gage wire and a 20 Amp rated outlet. If all of these are not the problem, then you have a bad motor that is partially burned out (that is, the insulation on the coil windings has melted and the coil wires are shorting out resulting in coils with a lot less turns than the motor was designed for. You can replace the motor or get it re-wound. Good luck!
Read More At : Table Saw...

We just purchased a used craftsman table saw model 113.29943 When we took it home and started using it, it runs fine when turned on , then slows down and sometimes stops when boards are ran through. We purchased a high quality new blade for it.


How thick are the boards you are putting through? maybe they are to thick also have you oiled the blade ? hope this helps John
Read More At : 10" Table Saw...

Delta Table Saw stopped running


I have a table saw that the cord from the motor plugs into the the back of the on/off switch. I yours is configured like that, unplug the motor cord from the back of the switch and plug it in to the wall and see if the motor will run. If so replace the switch.
Read More At : 10"Hybrid Tablesaw with 30"Unifence...

New table saw motor very weak and has problem kicking on


Is there an external phase shift capacitor for the motor? A defective phase shift capacitor can cause no or slow motor rotation and reduced motor power.
Read More At : Craftsman...

I own a Delta Shopsmart table saw model TS220LS and I have not used it for years and it still work but I don't know how to get the saw to rise above the table level. thanks.


On pos 75 page A turn the depth adjustment clockwise otherwise if its blocked by wood or other trash control the mechanic and clean it dry . Delta TS220LS TYPE 1 Bench Table Saw Parts
Read More At : Delta...

I was using my Delta TS220LS table saw and it quit running.


The schematic for this saw which you can see here: http://www.toolpartsdirect.com/cgi-bin/schematic.cgi/delta/TS220LS shows a circuit breaker associated with the motor. I do not know exactly where it is, you must find it and re-set it, problem solved.
Read More At : Saws...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0909 seconds