Guide :Saws : Saws

I was using my Delta TS220LS table saw and it quit running.

The motor does not even hum. The motor was not hot. I was only using it for about 1 minute before it quit. The blade does turn by hand with only slight resistance.

Research, Knowledge and Information :


DELTA TABLE SAW Parts | Model TS220LS | Sears PartsDirect


Shop for DELTA TABLE SAW repair parts for model TS220LS at Sears PartsDirect. ... to ensure proper fit and to keep appliances running for years to come.
Read More At : www.searspartsdirect.com...

My table saw motor just stopped.. What do I do?


I don't know why, but it works on my table saw everytime ... I gave up on the Delta parts and just bought a heavy duty 20 amp ... My table saw motor just stopped..
Read More At : forum.woodenboat.com...

Delta TS200LS Shopmaster 10" Portable Bench Saw with Legs ...


Delta TS200LS Shopmaster 10" Portable Bench ... This benchtop saw from Delta's Shopmaster line offers ... and a T-slot groove in the table so you can use a standard ...
Read More At : www.gosale.com...

repair - Why does the blade of my table saw stop? - Home ...


Why does the blade of my table saw stop? ... rhythmic ying-ying-ying noise when it is running. ... I had an older Delta saw that had a gearbox fail.
Read More At : diy.stackexchange.com...

10 Table Saw - media.ptg-online.com


10" Table Saw (Model TS220LS) ... Delta may cause damage to the machine or injury to the ... on the table/work area when the machine is running. 20.
Read More At : media.ptg-online.com...

Is Your Table Saw Motor Stopping, Stinking, Smoking or Silent?


Is Your Table Saw Motor Stopping, Stinking, Smoking or ... or it could create unusual sounds when the motor is running. Since table saws naturally ... My table saw ...
Read More At : www.toolerant.com...

Delta 34-670 table saw went dead, need advice - by Lloyd ...


I was cutting some 2 inch thick purpleheart with my table saw and ... Delta 34-670 table saw went dead, need advice ... I don’t know about the Delta but my saw has ...
Read More At : lumberjocks.com...

Delta Power Equipment Corporation - FAQ Search Results


FAQ Search Results. ... like to purchase the Delta t-square fence system to use on my older Delta table saw. ... Switch the table saw ON. 7. With the saw running, ...
Read More At : www.deltamachinery.com...

Suggested Questions And Answer :


I was using my Delta TS220LS table saw and it quit running.


The schematic for this saw which you can see here: http://www.toolpartsdirect.com/cgi-bin/schematic.cgi/delta/TS220LS shows a circuit breaker associated with the motor. I do not know exactly where it is, you must find it and re-set it, problem solved.
Read More At : Saws...

I was using my Delta TS220LS table saw and it stopped running.


I can solve your problem. I need a Delta TS220LS for parts and I do not care if it runs or not. I will buy the saw and you can buy a replacement. What do you say? Wayne Hill Anderson, SC 800 944.9577 864 356.3070 cell
Read More At : Saws...

Delta table saw, 34-670, keeps shutting down


There could be several problems. First, make sure you have a sharp blade. Then check the arbor for drag just after you have been using it. Unplug it, lift the motor a bit (to loosen the drive belt) and turn the blade with your hand - it should turn very freely. Check the motor shaft for drag too by turning the motor pulley with your hand (with the belt loose). The motor should have just a tiny bit more drag than the arbor shaft. If all of these check out ok, then you might have an insufficient gage of wire between the electric panel and the saw - a thin wire long extension cord is often a problem. If you are using an extension, try to eliminating it and plugging directly into the wall. (It depends on the length, but in general don't use a cord lighter than 14 ga - higher numbers mean skinnier wire). And it could be that the house wire is too light - a long run of 14 gage wire is too light - you want 12 gage wire and a 20 Amp rated outlet. If all of these are not the problem, then you have a bad motor that is partially burned out (that is, the insulation on the coil windings has melted and the coil wires are shorting out resulting in coils with a lot less turns than the motor was designed for. You can replace the motor or get it re-wound. Good luck!
Read More At : Table Saw...

What capacitor should be on a table saw motor


The part number you reference is a start capacitor. (details can be seen here: http://www.superioressex.com/uploadedFiles/Distribution/North_America/Essex_Brownell/Downloads/Linecards_and_Catalogs/capacitors_w.pdf ) It appears that the component capacitors (there are 2) are not available as separate parts from Delta. They only reference the motor itself (part 220 in the diagrams listed below.) http://www.ereplacementparts.com/delta-36650-type-table-saw-parts-c-3275_3334_13634.html At this point, I would try to locate another saw of the same model and read any numbers that may appear on the original capacitors on the motor. Please note the location and connections of each. There should be a run cap and a start cap on the motor. The differences between a 47uFD and 20uFD caps are not an issue in this application. Dan
Read More At : Delta...

I own a Delta Shopsmart table saw model TS220LS and I have not used it for years and it still work but I don't know how to get the saw to rise above the table level. thanks.


On pos 75 page A turn the depth adjustment clockwise otherwise if its blocked by wood or other trash control the mechanic and clean it dry . Delta TS220LS TYPE 1 Bench Table Saw Parts
Read More At : Delta...

I have an old delta tablesaw. It has a start and stop button. When the start button is pushed it used to start and run - now it only runs while the button is pushed. What is the problem? and how do I fix it?


Sounds like the on/off switch is bad. replace the switch with a switch that is of the proper voltage and rating value. a good place to find a switch is at your local hardware/industrial tool store. ( also try and find a switch at a industrial tool repair shop ). c...
Read More At : 1720305K 14" 7.5 HP 3 PH Model PM3000 Table Saw...

My Powermatic Model 64A table saw is 10 years old and has been lightly used as a hobby. It's powered to run on 230 volts. Beginning two weeks ago, the motor has begun to shut down during use. Sometimes it will re-start and work fine for an entire day and other times it will not re-start at all. Must dust collector runs on the same electrical circuit without problem. The table saw problem occurs with and without the dust collector drawing power. Tim in Knoxville Does this sound like a bad switch, lose electrical connection or a motor problem? Or, could it be something really simple that I'm overlooking?


Does wiggling the cord cause the problem?
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0613 seconds