Guide :Saws : 4000 - 07 Electric Table Saws

My saw runs backwards too!

The Bosch 4000. Did you figure out what caused your problem? Mine had run fine for a year and a half.

Research, Knowledge and Information :


Off Topic Circular saw spins backwards, any ideas ...


Off Topic Circular saw spins backwards, any ideas ... And some time in South Beach too. Ohh ... Putting the blade in a circular saw backwards is commonly used ...
Read More At : www.ecoustics.com...

Bosch tablesaw running backwards?!? | Fine Homebuilding ...


Bosch tablesaw running backwards?!? ... my tablesaw and said it started binding and he quickly shut off the saw. ... table saw like that too at least on a long ...
Read More At : forums.finehomebuilding.com...

Why does motor now runs backwards? - Saw - iFixit


Why does motor now runs backwards? ... 220 Volt Motor is on my Sears saw. ... Answer this question I have this problem too Subscribed to new answers
Read More At : www.ifixit.com...

Chainsaw Running Backwards. | Arboristsite.com


Chainsaw Running Backwards. ... Also if a saw was to run backwards you WOULD have to have the chain on backwards for it ... I couldn't figure out how it runs like that.
Read More At : www.arboristsite.com...

My peculiar nature: Bosch 4000 table saw fix (momentum lost ...


Jul 19, 2013 · Bosch 4000 table saw fix ... the speed either goes too high or the saw actually runs slow or backward. ... if your motor is running backwards ...
Read More At : mypeculiarnature.blogspot.com...

How To Use a Circular Saw brought to you by BARELYBAD


... volunteers are too loud and too powerful and too frightening to be used safely. If you don’t want to use a circular saw, ... want the saw to move backwards.
Read More At : barelybad.com...

Dolmar running backward? - The Forestry Forum


Yesterday a customer and I were quartering a red oak with my chainsaw, a Dolmar ... saw back up, the saw was running backwards ... a bulldozer,not too ...
Read More At : www.forestryforum.com...

Suggested Questions And Answer :


Bosch 4000 table saw run backward and slowly - Bosch 4000 - 07 Electric Table Saws


I had the same problem with the Bosch 4000.Changed the field for a new one...end of problem
Read More At : 4000 - 07 Electric Table Saws...

My bosch table saw runs slowly backwards what part do i replace


Replace the field coil. I'm going to bet its a Model 4000. I have done about 100 of these saws in the last couple of years and my customers always complain of the same problem, "the saw was running backwards" Change the armature back bearing while you have it apart, they always seize eventually.
Read More At : 4000 - 07 Electric Table Saws...

My saw runs backwards too!


Try to put the blade in the other way. then see if it works.
Read More At : 4000 - 07 Electric Table Saws...

My Powermatic Model 64A table saw is 10 years old and has been lightly used as a hobby. It's powered to run on 230 volts. Beginning two weeks ago, the motor has begun to shut down during use. Sometimes it will re-start and work fine for an entire day and other times it will not re-start at all. Must dust collector runs on the same electrical circuit without problem. The table saw problem occurs with and without the dust collector drawing power. Tim in Knoxville Does this sound like a bad switch, lose electrical connection or a motor problem? Or, could it be something really simple that I'm overlooking?


Does wiggling the cord cause the problem?
Read More At : 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30"......

My 4000 started running backwards very slowly - is it a field winding or maybe the speed controller? And if it is the speed controller, where is it and can I bypass it to test it?


I am not aware of any speed controller on this tool. what I would do is unplug tool and turn it on its backside and look at the switch to see if possibly burnt causing problems.
Read More At : 4000 - 07 Electric Table Saws...

Bosch 4000 table saw runs too fast - Bosch 4000 - 07 Electric Table Saws


Change the pulley on the motor to a smaller diameter to reduce the speed.
Read More At : 4000 - 07 Electric Table Saws...

Bosh 4000 table saw runs backward and at low speed


I've worked on some table saws with problems like you describe, a couple needed a new speed control unit (Bosch PN 2610997306) in the motor. If all the wiring to and inside the motor is OK and not shorting out anywhere, that's the next part you should look at.
Read More At : 4000 10IN Table Saw...

Bosch 4000 Table Saw running backward


You can find the 4000 manuals and parts diagram at bosch tools online. You will need a new armture Bnew bushes and possibly field. I would also replace the bearings and motor speed control circuit board. Bosch does not sell the motor assembly. Turn unit upside down and remove the Plastic body - approx 6 screws. Thake a digital camera and take LOTS of pictures of dissassembly as you will need them later. Blow unit clean and work neatly keeping all parts in labeled bins for reassembly. Don't attempt this job when your pressed for time. Before you start check to see if this machine is still under warranty!! Call customer support listed on website if you run into a problem. Good Luck !!
Read More At : 4000 Factory Reconditioned 10" Worksite Table Saw with......

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1112 seconds