Guide :Saws : 2703 10" Table Saw, Electric Brake

Makita table saw switch wiring

Somebody else pulled the switch out of my Makita 2703 saw. I have a new switch, but am not sure how to reconnect the wires. I tried a couple of ways, the saw works, but the electric brake does not. Any clues?

Research, Knowledge and Information :


Makita 2702 Table Saw Parts - eReplacementParts.com


Repair Parts Home Power Tool Parts Makita Parts Makita Saw Parts Makita Table Saw Parts Makita 2702 Table Saw Parts × 1 x ... a wiring diagram for the switch on ...
Read More At : www.ereplacementparts.com...

Makita Table Saw Wiring Diagram - Wiring Diagram Pdf Free


Makita table saw wiring diagram along with makita power tool replacement parts moreover input shaft motor in addition makita 2703 switch wiring diagram further makita ...
Read More At : myrockhair.com...

Makita Table Saw Switch Wiring Diagram - myrockhair.com


Makita table saw switch wiring diagram along with home depot logo photos in addition laser optique la science 160991 in addition jeep exterior parts diagram along ...
Read More At : myrockhair.com...

Older Makita Switch Wiring Help - Woodworking Talk ...


May 11, 2017 · I recently acquired an older (1985) Makita 2030N combo planer and jointer. Looks like a great machine but I need some help on replacing the current switch.
Read More At : www.woodworkingtalk.com...

makita saw switch | eBay


Find great deals on eBay for makita saw switch and start stop switch. Shop with confidence.

Switch (Ac/Dc) [651172-0] for Makita Power Tool ...


Buy a Makita Switch (Ac/Dc) ... Made a wiring diagram of the switch wires, ... I just replaced a new switch in my Makita circular saw Model# 5007NB.
Read More At : www.ereplacementparts.com...

Makita 2703 Switch Wiring Diagram - doahamba.com


Makita 2703 switch wiring ... saw. #makita 2703 portable table saw model. #makita model 2703 table saw dimensions. #makita 10 table saw with stand. #makita table saw ...
Read More At : doahamba.com...

Makita Table Saw modification | Fine Homebuilding | Breaktime


Plumbing & Wiring; Energy ... I have an old Makita 8 1/4" table saw, ... I used another long pop rivet through this end to penetrate the body and release the switch.
Read More At : forums.finehomebuilding.com...

Makita 2705X1 10-Inch Contractor Table Saw with Stand


Makita 2705X1 10-Inch Contractor Table Saw with Stand ... Connect the red wire from the circuit board to where the black wire came from (motor side) on the switch.

Suggested Questions And Answer :


Makita table saw switch wiring


After much trial and error, a little smoke, and wrecking one replacement switch, I solved a similar problem with my Craftsman Cmpd Mitre saw. Different saw, but likely the same principles are involved. If the switch is a double pole single throw switch, with one side normally open (N0) and the other normally closed (NC), and the saw has a separate wire for the brake, this will probably work. One side of the switch should have contacts that are normally open (NO) and only connect when the switch is ON. The Hot (Black) wire from the plug connects to the wire on the machine side (red or maybe black) through this NO side. So, connect these two wires via this NO side and the saw will run when the switch is ON but will have no brake; so far so good. There should be another wire (Not the neutral white) which is the brake wire. This gets connected to one of the connection sites of the Normally Closed (NC) side of the switch. From the other connection site of this NC side run a short "jumper" wire (of the same guage as the other wires) to the Machine Side of the NO side of the switch (same place as that Red or Black? wire above) . What seems to happen is this: There's no power to the machine or the brake when the switch is OFF. Turn it ON and power goes from Hot through the NO (now closed) side and the saw runs. The brake doesn't run when the saw runs because the NC switch is now open. Turn the switch OFF and the NC switch is in fact closed and power is transfered to the brake via the jumper wire from the still spinning armature which now acts as a generator (alternator?). Once the brake has done its job and the armature stops spinning there's no power anywhere until you turn the switch ON again. Or at least that's the theory, and in my case it works; no more smoke.
Read More At : 2703 10" Table Saw, Electric Brake...

Makita table saw switch wiring


I need the owner/operator manual for a makita table saw model 12711 please tell me what steps to take to get one
Read More At : Makita...

Switch wiring for makita cut off saw - Makita 2703 10" Table Saw, Electric Brake


Go to makita.com enter yr model # in the search bar, down load a parts breakdown, it should b there
Read More At : 2703 10" Table Saw, Electric Brake...

What is the most efficient way to remove and replace the switch on the Makita 2703?


There is only one way that I know of. Unplug tool and lay on its backside to expose the undercarriage of tool, remove the screws holding the switch plate on and remove box
Read More At : 2703 10" Table Saw, Electric Brake...

What would cause a table saw to just stop working?


Sound like the motor finally went to motor heaven. If you have an ohm meter do a continuity test of the motor. Should be a low ohm reading. If high or infinity, fogit it. One last thought! - check the motor brushes !!!!!!!!!!!!! If no contact with commutator the motor will not not be energized.
Read More At : Makita...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0904 seconds