Guide :Saws : Saws

Grizzly bandsaw cannot fit blade

Grizzly G0555 14'' bandsaw. Assembled and fit blade with no problem, but installed 6'' riser kit and the blade supplied is much too small. The riser measures 6''. The blade measures 105'' (correct size with riser), but even with top wheel lowered to maximum (minimum tension-- rotated spacers as far up the threaded rod as possible), the blade doesn't fit. The wheels are coplanar. With the tension arm in the ''up'' (tension released) position, I can get the blade on using considerable force. It's much, much too tight. Any solutions?

Research, Knowledge and Information :


Grizzly G0555 The Ultimate Bandsaw, 14-Inch - amazon.com


Grizzly G0555 The Ultimate Bandsaw, ... This Grizzly 14” saw has a blade to frame ... and while the tensioner can be adjusted to allow the 105” blade to fit onto ...

17" 2 HP Extreme-Series Bandsaw with Cast-Iron Trunnion ...


Grizzly | Model: G0513X2F. ... Noisey upper wheel which I cannot figure out where the noise ... My bandsaw blade came with a tag on it that said "Recommended for ...
Read More At : www.grizzly.com...

9" Benchtop Bandsaw | Grizzly Industrial


Introducing "The Cub" 9" Benchtop Bandsaw, Grizzly's first addition to our ... You cannot use a 3/8" blade because the bearing runs ... part fit well and it has nice ...
Read More At : www.grizzly.com...

Grizzly G0513 17" Bandsaw - 2 HP - Sears


Items sold by grizzly industrial, inc. cannot be returned to a Sears store seller's return ... This doesn't fit the vehicle based on ... Grizzly 17" Bandsaw - 2 ...
Read More At : www.sears.com...

Grizzly G0555 The Ultimate 14" Bandsaw - Sears


Items sold by Grizzly Industrial, Inc. cannot be returned to a Sears store seller's return ... This doesn't fit the vehicle based on ... Grizzly The Ultimate 14" Bandsaw.
Read More At : www.sears.com...

Grizzly H3051 Riser Block Kit for G0555 - - Amazon.com


Grizzly H3051 Riser Block Kit for ... Grizzly G0555 The Ultimate Bandsaw, ... excess powder coat but otherwise a direct fit. The long blade guard is metal and more ...

Band Saw Guide Upgrade Kits - Carter Products


Band Saw Guide Upgrade Kits; ... Bandsaw Guide Parts. ... or you cannot determine which guides you need for your saw, then don’t despair.
Read More At : www.carterproducts.com...

I want a New Bandsaw - Festool Owners Group


I want a New Bandsaw Hi, Guest ... manufacture for a saw with less hp and no blade brake. I have used a Grizzly resaw bandsaw ... and want the extra fit and ...
Read More At : festoolownersgroup.com...

Grizzly - Delta Bandsaws | Fine Woodworking Knots


Grizzly - Delta Bandsaws. Grizzly ... Could you tell me about the blade guides on the Grizzly saw? ... The Grizzly fit my non-existant tool budget at the time I ...
Read More At : forums.finewoodworking.com...

Suggested Questions And Answer :


Grizzly bandsaw cannot fit blade


I lowered the spacer (on the threaded rod) and got enough drop in the upper wheel to fit the blade.
Read More At : Saws...

I cannot get the blade to track correctly on my JET 12" band saw. What could be wrong? I have done exactly what the manual says to do. I am not sure the square box on the outside is fitting. The little arm that shifts the wheel does not look like it should just push against the side of the body. Should it not be just above the opening to be able to tilt the wheel properly?


I love bandsaws, they are one of best and most universal woodworking machines, used as well in food and metal industries.now, what you should know about bandsaw that it have several points of regulations and all of them must be adjusted correctly. basic "anatomy" of bandsaw is that it have body, in it there is driving wheel (bottom) and tension wheel (top), both of these are protected by rubber "tyre" usually crowned, that allow for bette adjustment and protect teeth on the band. start with tension, open covers, retract top (above the table) and bottom (below the table) guides so blade is not touching the rear bearing or side slides.1. rotate top wheel and see where blade is wandering, regulate tension and tilt on the wheel till band position itself on the centre of the top wheel and cuttin edge is off the wheel or rubber and do not touch the wheel or raiser.2. cut strip of paper and slide top guide towards the blade till bearing touch blade through the paper (paper thickness is about correct distance of bearing to the blade), allowing paper to be slided out without tension. lock it in.3. insert paper on internal side of the blade and slide internal slide guide block till you can only pull the paper out, lock the slider.4. repeat previous operation on external guide block and after you slide paper out, lock it in position.5. manually rotate the tension wheel, should operate freely, without wandering6. repeat step 2 to 5 on the bottom guide7. close the covers8. adjust hight of the guide suitable to cut , allowing about 2 finger breaths above the cut piece.9. switch on the bandsaw and switch off, after it stop, check for tension, switch on and make test cut.this general rule applies to all bandsaw, regardless of brand, make, vintage. do remember that this is not a toy, it will cut through, wood, metal and your fingers...do remember, that these operations must be performed every time when you change the blade, to not forget to use bit of silicone or teflon spray if you cut very sappy or green wood, do not press and force, use protection screen and googles, you have only two eyes and there are no spares...
Read More At : JWBS-16B 708749B 16-inch Bandsaw...

Craftsman 12" Bandsaw Blade Tracking Problems


Sounds like you have a saw with defective castings. Either cast out-of-true or deflect under pressure.
Read More At : Saws...

I brought a 3 pack tool set from Menards a drill, a saw and a flight light that the the 12 Voult


Google search the brand name. They will have saw blade sources.
Read More At : 12 Volt Lithium-ion Battery...

Does the bandsaw blade fit over the drivebelt .or run along side it on the metal rim


It runs along on the band saw wheel.
Read More At : Saws...

Makita slide compound- Saw Blade. LS0714


It seems as though the original blade was fitted without a spacer. These usually come with any new blade. It is simply a washer (usually aluminium) that fits in the hole of the saw blade and reduces the hole diameter down to the size of the flange on your saw. This is common practice. Never try and centre a blade without the correct size hole to flange size. Very dangerous. These washes are really cheap and can be obtained from most hardware stores. Usually in an assortment of different outside and inside diameters to suit any circumstance. Hope this helps, cheers Bob.
Read More At : Makita...

Have dewalt cordless jig saw. On opening the lift mechanism to take out the blade the lever napped. Try as a might I cannot see how it works to change the blade. The blade that is in there is useless and I cannot use the saw without changing the blade. Can anyone help??


Http://servicenet.dewalt.com/Parts/Search?searchedNumber=Dewalt+DC330K&searchType=1#
Read More At : DC330K XRP 18v cordless Jig Saw Kit with All - Metal Keyless......

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0903 seconds