Guide :Saws : Dewalt

Replacement of power cord on a Dewalt 708 type 3 slide mitre

My power cord shorted out right at the end of the slide tube, how tough is it to replace myself ?

Research, Knowledge and Information :


DeWALT DW708 Type 4 Replacement CordSet # 330079-24 ...


DeWALT DW708 Type 4 Replacement CordSet # 330079-24 ... DeWALT DW708 Type 4 Replacement CordSet # 330079-24 ... DEWALT 33007898 2 Wire 16 Gauge Power Cord, ...

DeWALT DW708 TYPE 3 Crosscut Miter Saw Parts


Need to fix your DW708 Type 3 Crosscut Miter Saw? ... DeWALT DW708 TYPE 3 Crosscut Miter Saw Parts. ... Power Cord - 10', 16 Gauge, 2-Wire
Read More At : www.ereplacementparts.com...

How to Replace the Cord on a DeWALT DW708 Miter Saw ... - YouTube


May 22, 2012 · Follow the steps in this video to easily repair your DeWALT DW708 miter saw power cord. Useful tools include a wire cutter/crimper, a screwdriver, needle ...

Quick Fix: How to Replace the Cord on a DeWALT DW708 Miter ...


Shop By Brand Shop By Tool Type. ... Swing by our DeWalt parts page to find the replacement parts for your on ... replace the power cord on your DeWalt DW708 miter saw.
Read More At : www.ereplacementparts.com...

DeWalt Miter & Circular Saw replacement 10 Foot Cord - 330078 ...


DeWalt Miter & Circular Saw replacement 10 Foot Cord ... Home > Power Tools > DeWALT > Parts > Cords ... This cord will fit the following DeWalt Saws: DW704 Type 3 12 ...
Read More At : www.mendingshed.com...

DeWalt DW708 Type 2 Mitre Saw Spare Parts - Part Shop Direct


DeWalt DW708 Type 2 Mitre Saw Spare Parts ... DeWalt CORD CLAMP DW708-2-98-153669-00 ... Power Tool Centre Limited
Read More At : www.partshopdirect.co.uk...

DW708/eng. - DeWalt


WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. ... disconnect cord from power source and ... or more will cause a loss of power and overheating. All DeWalt ...
Read More At : documents.dewalt.com...

DeWalt Miter Saw Parts - Master Tool Repair


Get DeWalt Cordless or Corded Miter Saw Repair Parts at Master Tool Repair. Easy online ordering, helpful sales staff and tech docs available.
Read More At : www.mastertoolrepair.com...

Suggested Questions And Answer :


Replacement of power cord on a Dewalt 708 type 3 slide mitre


Not that bad, I would go to Dewaltservicenet.com and look at an explosion before taking yours part. You have to remove the top of the handle, there is cover on the side towards the blade that is tight to remove and then the strain relief on the tube. The cord set that you need is 330078-98 list for 16.76. It is a 10ft 16-2 wire. Just take your time and if you are handy with tools you should have no problem. Let me know if I can help I work on them all the time.
Read More At : Dewalt...

I need a repair manual to show assembly of the power switch


Not sure about the repair manual.. here is a link to the schematics I used: http://www.toolpartsdirect.com/cgi-bin/schematic.cgi/makita/LS1013FL For better view use the PDF version.
Read More At : LS1013FL 15 Amp 10 Inch Dual Bevel Compound Sliding Miter......

Power cord on DeWalt electric drill


Dbx is a family of noise reduction systems developed by the company of the same name. The most common implementations are dbx Type I and dbx Type II for analog tape recording and, less commonly, vinyl LPs. A separate implementation, known as dbx-TV, is part of the MTS system used to provide stereo sound to North American and certain other TV systems. The company – dbx, Inc. – was also involved with Dynamic Noise Reduction (DNR) systems. My conclusion is that your answer was right on.... good work.
Read More At : Saws...

I cut the power cord on a milwaukee magnum slide compound miter saw. How do I replace it?


Go to: http://www.milwaukeetool.com/PartsAndService/Repair/Default.aspx
Read More At : 10" Magnum Compound Miter Saw...

I'd like to know how to replace the extension cord on my DeWalt 12" sliding compound miter saw. Also the wing nut on the back cannot be tightened enough so that when cutting crown at odd bevels, the saw falls down to 45 degrees.


Rempve the lead from the wall socket. To replace the lead on an tool, open the cover where the cord enters the tool and undo the cable clamp. Undo the cables where they attach to the tool switch and the earth etc., taking note of the colour coding of the wires. Transfer the rubber cable protector, if you can remove it, to the new cable and fit the new wire in the same position and colour connections as the old one, refit the clamp and replace the cover. Place a thick washer the size of the bolt under the wing nut that locks your angle adjustment. This should take up the slack and allow you to tighten the wing nut.
Read More At : Dewalt...

How to replace a power cord on a B&D 7340 type 2 circular saw?


It's not difficult. Open the saw up, and the power cord is pretty much right there. Get a new power cord from B&D, that will be easiest.
Read More At : Saws...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0400 seconds