Guide :Saws : Craftsman

Band Saw Blade won't stay on

Recently obtained a Craftsman 10" Band Saw Model 113.244513. The blade was not on it. Found a manual online and thought I did everything according to the directions but every time I turn it on the blade runs off the wheels.

Research, Knowledge and Information :

Bandsaw Tune-Up + Installing a bandsaw blade -

The procedure of making a band-saw behave consists of two basic ... Blade doesn’t stay centered on wheels Wheels, Blade guides ... bearing that is noisy or won’t ...
Read More At :

Bandsaw tire replacement won't stay on.... | Sears PartsDirect

Bandsaw tire replacement won't stay on ... band saws are great for projects and making stuff. the tire not staying on the band saw can be very frustrating ...
Read More At :

Band Saw Blade Tension, Tracking and Guide Blocks

How to replace and set your band saw blade tension, ... and guide blocks. Keep your band saw operating ... (where the blade doesn’t cut true and won’t easily ...
Read More At :

Woodworking Bandsaw Tires

Really bad tires won't even stay on the wheel. ... The tire is also important in blade tracking. Most band saw tires will be ... Not all bandsaw tires are ...
Read More At :

Fine-Tuning a Bandsaw - Central Coast Woodworkers Association

Fine-Tuning a Bandsaw ... If the band moves off the center ... Blade drifts and won't follow line. Not enough set in blade; upper guide is set
Read More At :

Bandsaw Blade won't stay on wheels - by wes3 @ LumberJocks ...

Bandsaw Blade won't stay on wheels « back to Power Tools, Hardware and Accessories forum. Forum topic by wes3: ... You need tires on a band saw because without
Read More At :

Why won't the blade stay on my Craftsman 10" band saw model ...

Get shopping advice from experts, friends and the community! The new band saw blade will not stay o the machine for cutting.
Read More At :

Band Saw Blade won't move when motor runs | Symptom Diagnosis ...

Learn why your Band Saw Blade won't move when motor runs at Sears PartsDirect. Find out which repairs might help solve the problem, parts and more.
Read More At :

Suggested Questions And Answer :

Band Saw Blade won't stay on

A lot of the larger band saws, and I don't know about your particular model, has an ajustment on the bottom wheel that tilts the wheel in order to track the blade. It is right at the axle and tilts it from there.  If the back guide is a roller bearing I woud think you would want to roll all of the time.  If a solid bearing block natually a small space where it  will not hit is enough.   
Read More At : Craftsman...

Can I use Craftsman 99-3/4 in. Band Saw Blades - 3 pk. on my craftsman 14" bandsaw #124.32607

I think you need a specialist to answer your questions and can give you some options. You may want to give a call to . You can contact this 201-450-9810 or visit to their website . Hope that helps.
Read More At : Saws...

8 inch delta band saw that cant keep the band in place in use

The rubber bands on the metal wheels are called tires, and if they are cracked, they may very well be crowned and causing the problem with the band coming off.To test, remove the back guide (as opposed to the side guides) on the top and bottom guide sets (above and below the table.). Put a blade on, and see if it will stay on. If it doesn't, replace the tires. If it does, reinstall the back guides and make sure they do not touch the back of the blade when the saw is running. There should by about 1/32" between the guide and the blade.
Read More At : Saws...

Blade will not stay on - Craftsman 113.243300 & 113.243311 12" Band Saw Sander Operator Part Manual 0177

There are number of reasons why : Incorrect tension , wore/ loose tiers, Improper guide adjustments. Also , visit this link for your manual .
Read More At : 113.243300 & 113.243311 12" Band Saw Sander Operator Part......

Need owners manual for a craftsman band / need help troubleshoot

Hi, On all bandsaws, it's the pitch of the wheels that determine the position of the blade. The top wheel should be adjustable for pitch, and blade tightness. The blade should only contact the thrust bearings when you are cutting, not when it is idling. No sense in wearing out the bearings and blade while idling.
Read More At : Saws...

Craftsman model 708100 table saw tilt lock won't stay locked

Try removing the lock knob and putting a toothed lockwasher on the shaft. reinstall the knob.
Read More At : 10" Table Saw...

The guide assembly on my 14" band saw will not stay peralell with the blade as it goes from the top of its travel to the bottom. it goes right to left going up and reverse going down the blade . the o

Sounds like something's bent. You might need some replacement parts. 14" band saws, regardless of brand, are generally made with Chinese parts that are knockoff Delta-Rockwell parts from many years ago. Grizzly sells most of these parts at reasonable prices. Check the exploded views of their saws to see if the parts match. Craftsman parts are expensive, even though they're the same part.
Read More At : Products Rikon 14" Sears 14" Professional Guide Conversion......

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0710 seconds