Guide :Saws : Saws

Table saw won't turn on.

Was using Craftsman table saw/model 137.248830. Went to make another cut, and it wouldn't start. Blew sawdust from box containing switch and reset button. Still won't start. Reset button seems "soft", like I"m really not pressing anything.

Research, Knowledge and Information :


Table saw won't turn on. 113198610 Craftsman ... | Sears ...


Table saw won't turn on. 113198610 Craftsman 10-inch deluxe electronic radial saw | SearsPartsDirect
Read More At : www.searspartsdirect.com...

My 10" Table Saw Will Not Start. | Sears PartsDirect


My 10" Table Saw Will Not Start. I have an old 10" Kenmore Craftsman table saw model 113.298051. It will not turn on. The switch doesn't seem to be making a connection.
Read More At : www.searspartsdirect.com...

Is Your Table Saw Motor Stopping, Stinking, Smoking or Silent?


Is Your Table Saw Motor Stopping, Stinking, Smoking or ... It won’t turn on ... If you have a benchtop or small portable table saw you can slowly turn it upside ...
Read More At : www.toolerant.com...

Table saw won't turn on.. - by MissouriOutdoors88 ...


So I just got done replacing the dinosaur era blade on my old 1 HP compact table saw (Black and Decker, 8 inch) with a new freud. Pulled it to give it a test, and it ...
Read More At : lumberjocks.com...

Craftsman table saw motor hums but won't spin - Woodworking ...


Craftsman table saw motor hums but won't spin. ... The motor won't turn even with the belt off. It did work, but now just hums. I've just pulled it and taken the ends ...
Read More At : www.woodworkingtalk.com...

My table saw motor just stopped.. What do I do?


I did the same thing on my table saw and radial arm saw, ... My table saw motor just stopped.. What do I do? ... it won't start suddenly by itself.
Read More At : forum.woodenboat.com...

Problems With a Table Saw Motor | Home Guides | SF Gate


Problems With a Table Saw Motor. ... The first place to look for a problem when a table saw won't start ... If the motor simply hums or starts slowly when you turn ...
Read More At : homeguides.sfgate.com...

My Rigid 4510 Table Saw Wont Start - Tools & Equipment ...


My rigid 4510 table saw wont start up. I made one cut with it turned it off then when I went to restart it nothing. I am not very mechanically inclined, I can build ...
Read More At : www.contractortalk.com...

Delta 34-670 table saw went dead, need advice - by Lloyd ...


I was cutting some 2 inch thick purpleheart with my table saw and all of a ... table saw went dead, need advice ... and when I flip the switch again it won’t ...
Read More At : lumberjocks.com...

Suggested Questions And Answer :


Bosch table saw model 4000


It sounds like the pinion on the armature and or gear are stripped. The only way to find out is to tilt the blade and remove the motor housing from the diaphragm and check it. If replacing the armature I would recommend also replacing the bearings and brushes as preventative
Read More At : Saws...

Tile saw stopped working


Check the motor might have a reset botton or check the capacitor
Read More At : DW746X 10" woodworker's table saw with rai...

My tablesaw wont speed up and run. Bosch 4000 ten inch. It makes a klunk and starts to turn and slowly speeds up until its running, but still makes a knocking sound


Is it spinning the blade at all? If it is then it is unlikely to be an electrical fault. Have you considered a motor bearing fault? If the motor bearings are worn, it could turn freely by hand, but when powered up it would stutter and stall. The motor is basically a big electro-magnet so if the armature has enough lateral movement, when it is magnetized it could rub against the stator. If the machine is buzzing, but not spinning the blade it is more than likely going to be caused by a faulty capacitor as this is the component that gives the motor the initial 'kick' in the right direction to get it spinning.
Read More At : Electric Table Saws...

I have a Craftsman table saw a few weeks back had problems getting the saw to run....would have to hit the switch several times to make it run. Once it was running it was good until I shut it down, then I would have to hit the switch 5 or so times to get it to run again. Today it did the same thing and now just wont run. The blade turns freely by hand and is not binded or anything. Does this sound like a bearing? Brushes?


Replace the switch? Hello!
Read More At : 10" Table Saw...

I have a delta contractors table saw that wont start. It has a Marathon Electric Motor 62-044 that hangs off the back. It has capacitors rather than brushes. When you turn on the swithch it does nothing. I checked the power to the saw an its good. I think it may be the capacitor(one or both). When you turn on the switch it does nothing no buzzing nothing. Is it the capacitors and do I have to split the motor(pull out the long bolts that run all the way thru the motor to get at the base of these capiaitor wires or not. Ideas????


Most likely to quit suddenly is the switch.My table saw switch broke recently, and at first I thought it was the motor.Over the years I remember seeing table saws fitted with a handy box and ordinary light switch to replace the table saw switch.Check for power at motor: Sometimes the wire connection from switch has access box on the motor where you can get in and check for power.
Read More At : 36-979 10" Left-Tilt Contractor's Saw...

When I loosen the handle to turn my saw, the table is extremely tight and wont turn. It was fine when I put it in the truck the other day?


If it was fall ornot beaten by other falling tools in your truck and have no warranty loose a central locknut in the middle of the bottom to remove the bottom plate clean it from possible blocking dirty and mount it together again. Don,t tighten it to fast but so you like but just no tolerance has.
Read More At : 12" Dual - Bevel Compound Miter Saw with Upfront Controls......

Bosch 4000 table saw wont power on


The field is notorious for failing in these tools - If you remove the cap on the field housing you can access the field wires - check to see if you have continuity through the field windings. To further investigate 1) Remove the brushes and inspect them for excessive wear or chipping (If they look burnt or are chipped the armature is suspect) 2) Remove the 4 screws holding the field assembly to the saw frame 3) Pull the field off and inspect the armature (especially the commutator (copper segments the brushes ride on) for burnt or raised segments or windings.
Read More At : Work Site Saw 4000-09 With Gravity Rise Saw Stand...

My saw was working fine yesterday, and today it will not turn on. the motor wont even kick a lttle, i flip the on switch and nothing.


With a volt meter See if you are getting 110 volts to the switch and then see if your getting ower from the switch to motor.
Read More At : 2704X1 Electric Table Saws...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0865 seconds