Guide :Saws : 9015A 5" Electric Angle Grinders

Help please looking were to find brushes and fields for my makita 9015a 5 l in. grinder

Posted by papa t88 on Jan 22, 2009

Research, Knowledge and Information :


Makita Parts - eReplacementParts


We have the genuine Makita parts and tool repair help you need to get your power tools running like new again. ... How do I find my model ... carbon brushes, air ...
Read More At : www.ereplacementparts.com...

5 Reciprocating Saw Accessories You Should Own | Power tools ...


5 Reciprocating-Saw Accessories You Should Own ... Once you attach a wire-brush accessory to your recip saw, ... My joints were... Find this Pin and more on workbenches.
Read More At : www.pinterest.com...

Electric Power Tool Parts 101 : eReplacementParts.com


Electricity is carried from the power switch to the tool's Carbon Brushes ... just by looking ... parts inventory to find the electric power tool parts ...
Read More At : www.ereplacementparts.com...

Replacement Parts | Boschtools


"Bosch original replacement parts are developed and ... For quick "run-in" of brushes and reduced ... Please fill in all required fields including your ...
Read More At : www.boschtools.com...

SE2986 - C/T Countertop Planer x 2-1/16 | Products, Planer ...


SE2986 - C/T Countertop Planer x 2-1/16" CD x 1/8 CL
Read More At : www.pinterest.com...

Metabo - Power Tools for professional users


Metabo is a manufacturer of power tools and supplier of accessories for professional users. ... 5" Angle grinder 0,00 ... use from our fields of competence ...
Read More At : www.metabo.com...

18V Brushless Hammer Drill Showdown 2 – Dewalt vs ... - Coptool


18V Brushless Hammer Drill Showdown 2 ... the folks at Ohio Power Tool were doing with their staff to ... but ever since I got my hands on makita drills I ...
Read More At : www.coptool.com...

And - antiquewoodfinish.org


Of course they were Find ... Floors an ordinary drill but is looking much improved. Remember, these are my ... Alaska to help the first time. Notice that the field ...
Read More At : antiquewoodfinish.org...

Cheap and Easy Garage Workbench | Garage workbench


I recently wrapped up the construction on my new work surface / workbench in the garage at our new home. The final measurements are 12 feet long, 2 feet deep, w
Read More At : za.pinterest.com...

Hi this is my take on a homemade table saw, router table and ...


Hi this is my take on a homemade table saw, router table and inverted jigsaw, I built all 3 into the same table to save on space I am very pleased with the r...
Read More At : au.pinterest.com...

Suggested Questions And Answer :


Help please looking were to find brushes and fields for my makita 9015a 5 l in. grinder


You can also go to Acklands (or grainger in the USA). They have all the parts just not listed in the catalogue.
Read More At : 9015A 5" Electric Angle Grinders...

Bosch angle grinder


Replace capacitor, Yes it would give those symptoms
Read More At : Bosch...

Bosch angle grinder acts like its burnt out but motor resistance values suggest not


Hi Brian, running your angle grinder on reduced voltage (through overloading the petrol generator) will have caused the current in the grinder to be higher than it should be. This may not be what you expect, but it is a characteristic of rotating machines, they behave differently to resistive machines such as heating elements. You have not indicated how you come to the conclusion that the windings test OK. If you have just checked with an ohm-meter and see a continuity reading, this does not eliminate the possibility that the overheating resulting from over-current has broken down the insulation (evidenced by the smell and sparks) and you have short circuited windings. The grinder will run without a suppression capacitor, it is just there to minimise interference with you neighbour's (or your wife/girlfriend/daughter's :) ) radio. Replacing the capacitor will not restore your grinder, I reckon you have killed it, in spite of the fact that running it on a healthy supply was to quickest way to cool it effectively.
Read More At : Bosch...

Angle grinder eats carbon brushes


Yes, the rock dust is what's destroying your brushes and armatures. It gets sucked into the rear vent slots and gets to those parts and eats them away quickly. I don't know of any vacuum systems make by Makita but there are some companies that make them for their systems. Blastrac is one that comes to mind but they can be real expensive systems. I don't know of any grinders with sealed brush/armature systems, they have too much heat to disipate. To make your Makita grinders last longer make sure you are cutting with the side of the blade that directs the dust away from the case and try to have a strong airflow blowing the dust away from the grinder to minimize the dust taken in at the back of the grinder.
Read More At : 9005B 5" Electric Angle Grinder...

Dewalt dw474 grinder quit


You need new brushes. carbon is meant to be touching the armature not the contact from the spring. Its worn down
Read More At : DW824 5" Electric Angle Grinder...

Armature problems Can anyone tell me how to remove the armature for inspection on a makita 5" angle grinder model 9005b?


Http://www.toolsandmachinery.com/blog2/tag/repair-9564cv-grinder/
Read More At : 9005B 5" Electric Angle Grinder...

How to fix makita 5" grinder


It is time to replace the trigger switch.
Read More At : 9005B 5" Electric Angle Grinder...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0372 seconds