Guide :Saws : 10" Miter Saw LS1030N

Makita LS1013 chop saw just started making a bad bearing noise and the elecric brake is not kicking in after the trigger is released.

Posted by doug166 on Jan 23, 2009

Research, Knowledge and Information :

Makita LS1013 Miter Saw Parts -

Need to fix your LS1013 Miter Saw? We have parts, diagrams, accessories and repair advice to make your tool repairs easy.
Read More At :

Carbon Brush Set [CB154] for Makita ... - eReplacement Parts

Buy a Makita Carbon Brush Set [CB154] for your Makita ... of electricity when the trigger is released, ... like a spun bearing.With the saw unplugged can you ...
Read More At :

Makita UK

ENHANCE OFFICE CLEANING LIMITED COMMITTED TO MAKITA BACK-PACK VACUUM CLEANERS Makita back-pack vacuum cleaners are now part of the inventory of Enhance Office ...
Read More At :

Makita LS1016L 10 in. Dual Slide Compound Miter Saw with Laser

The Makita LS1016 10 in. Dual Slide Compound Miter Saw is the largest crown molding ... Even after just a few ... no real need to get an expensive chop saw ...
Read More At :

Miter Saw Tune-Up | THISisCarpentry

... I frequently use both the chop saw and the ... Knowing your saw means practicing and perfecting your miter saw ... It looks level but it’s just not co ...
Read More At :

Top 52 Complaints and Reviews about DeWALT Tools

... I thought it was probably just a bad batch ... The person in the service center verified it was not damaged, and after making a copy of ... DeWalt Chop Saw ...
Read More At :

TraderTAG - Victoria - Edition 28 - 2016 by TraderTAG Design ...

Issuu is a digital publishing platform that makes it simple to publish magazines, catalogs, newspapers, books, and more online. Easily share your publications and get ...
Read More At :

Anybody use Ryobi tools? [Archive] - WeldingWeb™ - Welding ...

The drill doesn't have a shaft brake, making it very ... a lot of bearing noise and seems ... cordless circular saw I got in a kit; just not enough poop ...
Read More At :

Suggested Questions And Answer :

Makita LS1013 chop saw just started making a bad bearing noise and the elecric brake is not kicking in after the trigger is released.

Read More At : 10" Miter Saw LS1030N...

Delta 36-075 miter saw. Motor ok, but blade will not spin

Http://$9.60+ $11.59 postagenot sure if this right one You might get these on Ebay im not sure which country you are in this might guide you to one you could get this on Ebay if you dont have an account you will need to create one Add Email adress Add Bank Acc Add Credit Card also add your postal adress also add a paypal account when you get to the paypal login page at the bottom you will see new to paypal sign up tab paypal to create an account paypal registration password ,bank card /credit card,phone numbers home/mobile ,email adress and a postal adress be very specific when you type in the search always ask questions? before you make a purchase and keep the email/s for security reasons if the item arrives and its not as described you will even see the pictures of your item so you cant make a mistake and get them home delivered hope this helps you
Read More At : Delta...

Makita Saw blade brake doesn't work.

I have a makita still saw put i pull cored but it dose'nt start
Read More At : 10" Miter Saw LS1030N...

Re: ryobi tss100l on releasing the trigger the saw motor keeps running, but the brake is applied, stopping the blade, and finally blowing the 15 amp circuit breaker... thanks frank leppa

089100118042 switch ~ about $8 at ereplacementparts. The brake feature does not use 115v power to work. It uses self generated energy from spinning armature to work. When you release the switch, 115v power is disconnected and brake circuit is activated. Looking at the wiring key on the side of the switch, there are two switch positions with connections numbered from one thru four. Connection 1 to 2 is the normal open connection and is where the motor run wires are connected. Second position is 3 to 4 that is normal closed for brake. Some replacement switches are numbered differently so just follow marked wiring pattern. Your switch is apparently faulty. As a temp measure, try removing one lead of brake circuit from the switch to see if it allows you to use the saw without brake feature. Only a temporary fix if it works untill new switch arrives allowing you to keep working.
Read More At : 10 In Miter Saw With Laser...

Brake Blade does not shut down after releasing the trigger

Check the connection on the safety!
Read More At : 10" Miter Saw LS1030N...

Can't release the trigger lock on the makita 255mm

Do you mean you can't depresss the trigger lock to activate the switch or it won't return to lock the switch, let me know which it is and I will try and help, also you can look at the breakdown for this tool at by typing in your model number so you know what the parts look like and the assembly.
Read More At : 10" Miter Saw LS1030N...

Miter Saw - Makita LS1040. Electric brake function does not work

How do the brushes look?
Read More At : 10" Compound Miter Saw LS1040...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0699 seconds