Guide :Saws : & Variable Scroll Saw

Dewalt DW788 scroll saw noise

My scroll saw has started making a loud rattling/clattering noise. I have sent it back once for repair and the noise went away for awhile. The saw was out of warranty the first time I had this problem but it was still repaired free. I have now owned the saw about 5-6 yrs. I don't use it that much anymore. The noise goes away when I slow the speed down. Any help would be appreciated. Jerry

Research, Knowledge and Information :

20" Variable-Speed Scroll Saw - DW788 | DEWALT

The DW788 20" Variable-Speed Scroll Saw operates quietly and smoothly for accuracy. The tool-free blade clamp allows for quick and easy blade changes. Convenient ...
Read More At :

DeWalt 20'' VS Scroll Saw (DW788) with Cast Iron Table ...

DeWALT's 20'' VS Scroll Saw features a double parallel-link arm design which dramatically reduces vibration and noise which allows for more accurate cuts.
Read More At :

Dewalt DW788 Knocking Noise - (Fix) - YouTube

Feb 22, 2016 · Over the last 15 years, I've had to tighten the bolt inside my Dewalt scroll saw two times. I noticed the saw was knocking which means the bolt has come ...

New DeWalt 788 Rattling Noise ...normal or not? - by Vinnie ...

I just got a new DW788 and and my saw has a rattling sound sometimes ... New DeWalt 788 Rattling Noise ... can compare the sound of they’re DeWalt 788 scroll saw .
Read More At :

DEWALT DW788 1.3 Amp 20-Inch Variable-Speed Scroll Saw ...

DEWALT DW788 1.3 Amp 20-Inch ... Double parallel link arm design dramatically reduces vibration and noise, ... This 20-inch variable-speed scroll saw comes with a ...

DEWALT 20 in. Variable-Speed Scroll Saw-DW788 - The Home Depot

DEWALT Variable-Speed Scroll Saw features double parallel-link arm design for accurate cuts and arm pivots from back to the front.
Read More At :

My old scroll saw dewalt dw788 start making a knocking sound

My old scroll saw dewalt dw788 start ... i'll wait for awhile and get a 2014 dw788 scroll saw I still got my old scroll saw the 2012 but that got a knocking noise.
Read More At :

DEWALT 1.3-Amp Variable Speed Scroll Saw - Lowe's

Shop dewalt 1.3-amp variable speed scroll saw in the ... Double parallel-link arm design dramatically reduces vibration and noise, ... Includes DW788 scroll saw, ...
Read More At :

Scroll Saw Model DW788 - Woodcraft

Model DW788 - DeWALT 20 Heavy Duty Variable Speed Scroll Saw 13 Amp 400-1750 strokes per minute 20 throat The oversize cast iron table tilts 45 degree left and right ...
Read More At :

Tune -

Tune-Up & Repairs to the Dewalt ... George North complained of excessive noise coming from his DeWalt scroll saw and asked if I ... the newest crop of DW788 Scroll ...
Read More At :

Suggested Questions And Answer :

Dewalt DW788 scroll saw noise

Hello,,,i just bought a new dw788
Read More At : & Variable Scroll Saw...

How to install air hose on dw780 scroll saw - Dewalt DW788 Heavy Duty 20" Variable Speed Scroll Saw: DW7881 Worklight

I found other sources that suggested heating the end of the hose with hot water or a hair dryer. Once it softens slightly you can push it on the metal ball with your hand. A hair dryer did not work for me, so I set the end in almost boiling water for 2 minutes. I tried shorter amounts of time first, but it took a full 2 minutes to work for me.
Read More At : DW788 Heavy Duty 20" Variable Speed Scroll Saw: DW7881......

Saw has no power.

Does the motor continue to run, but the arm stops? It sounds like the set screw on the motor shaft is loose. See the exploded view at this link. It's called out as # 97
Read More At : DW788 Heavy Duty 20" Variable Speed Scroll Saw: DW7881......

Cannot access fuse in a dewalt scroll saw dw788

Hi, if the fuse has never been changed it may just be stiff, also whenit says push it may be that your are not pushing in the right directionsome have to slide and push at the same time, however, assumingyou have tried this, then it would make sense to revert to the screwdriver method , but gently and at the opposit end from the word push...T.C.
Read More At : DW788 Heavy Duty 20" Variable Speed Scroll Saw: DW7881......

How can I cut wood 3.5 inches thick with Dewalt Scroll saw?

Nope... throat on scroll saw is of fixed height... beside, all scrollsaw blades are of fixed length, i would suggest use of bandsaw with very narrow blade with minimal kerf. do not use pressure on the blade! you will then have same cut through the thickness of the wood! setup bandsaw correctly, do not overtension it - see my other instructables pertaining to the bandsaw and regulation/setup of it if you find my solution helpful - do not me shy... give some points... :-)
Read More At : DW788 20" Variable-Speed Scroll Saw...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0576 seconds