Guide :Saws : 14" Band Saw with Stand

Wheels won't turn

Of course I called Ridgid and I have to carry this thing over 150 miles to get it fixed so if I can do it myself it would save me a bunch of time but when I turn it on I get nothing. I checked all of the obvious to make sure power supply was coming in. Just before it went out completely one day I went to turn it on and the blade stopped, the motor hummed for aprox. 15 seconds then nothing. Of course my assumption is the motor is blown but where would I get a new one or is this one just worth driving the 150 miles and dropping it off and hoping they come up with something that is supposed to be

Research, Knowledge and Information :


Sep 17, 2007 · Mix - B.T.O - MY WHEELS WON´T TURN YouTube; Bachman Turner Overdrive Down Down - Duration: 4:26. grvnmj 310,942 views. 4:26.

B.T.O. (Bachman-Turner Overdrive) Lyrics - My Wheels Won't Turn

Lyrics to "My Wheels Won't Turn" song by B.T.O. (Bachman-Turner Overdrive): I met a man who bought up land Wherever his feet would tread He asked me to El Paso Said I ...
Read More At :

What should I do if my steering wheel doesn't turn ...

A steering wheel that does not turn is usually an indication the power steering assembly is malfunctioning. There are several components to a power steering assembly ...
Read More At :

Bachman-Turner Overdrive - My Wheels Won't Turn lyrics ...

My Wheels Won't Turn lyrics by Bachman-Turner Overdrive: I met a man who bought up land / Wherever his feet would tread / He asked me to El
Read More At :

BTO ~ My Wheels Won't Turn - YouTube

Jul 02, 2015 · Bachman–Turner Overdrive is a Canadian rock group from Winnipeg, Manitoba, that had a series of hit albums and singles in the 1970s, selling over 7 ...

Rear wheels won't turn... - Yesterday's Tractors

The rear end is up on blocks, still attached to the rest of the tractor. I took the left axle housing off and the ring gear out. The bearings and cone
Read More At :

wheels won't turn - DIY Chatroom Home Improvement Forum

wheels won't turn, took off bottom face plate nothing appears to be blocking ...?
Read More At :

Front wheels won't turn right - Maintenance/Repairs - Car ...

My son wrecked his 01 Honda, front drivers side front. After replacing his wheel and headlight, his front wheels will turn left but won't turn right all the way.
Read More At :

Steering wheel does not turn car Inspection Service & Cost ...

Steering wheel does not turn car Inspection ... turning your steering wheel while the car is running turns the wheels themselves. The steering wheel is the only means ...
Read More At :

wheels won't turn | Shop Your Way: Online Shopping & Earn ...

Get shopping advice from experts, friends and the community! model.107.250070- CTX - 9500 - Garden Tractor-Craftsman I already installed steering wheel on tractor ...
Read More At :

Suggested Questions And Answer :

Delta 28-160 band saw 3 wheel, blade keeps coming off

Sounds like your tracking screw needs adjustment, located right beside the knob used for tightening after adjusting the tension on the blade. Allen wrench required. Turning right pushes out and turning left pulls it in. A little is a lot when adjusting this screw. Always turn the blade in the same direction as the cut while adjusting.
Read More At : 28 276 14" Band Saw W/ 3/4 Hp Motor & Open Stand...

Rigid 14" Band Saw Stand Bounce

Yes, take it back to the store that sold it and get them to replace or repair the problem. Hope this helps!
Read More At : 14" Band Saw with Stand...

Wheels won't turn

OK I checked a couple sites and depending on the model number one of the motors is obsolete, the other is about 240.00 list. Are you sure the motor is bad? If so what I would do is if you have a local Grainger supply center give them the numbers off the motor and let them match it up with a Dayton motor. I didn't see anything special on the one that I looked at. It appears to have a straight shaft with a keyway for the pulley. Before I drove the 150 miles double check the motor and also it appears that it has a capacitator to check also. Let me know if I can help further but I wish I had better info for you.
Read More At : 14" Band Saw with Stand...

Turn saw on, Curcuit pops immediatly

The motor is bad. It is drawing too many amps.
Read More At : 3385-01-RT Factory-Reconditioned 9" Band Saw with Light...

Rubber bands pop off of wheels

My Delta 14" had the same problem. My fix was to get new rubbers, took care of my issue. They do stretch, but the newer the rubbers are the more the will retain there form, the older they are, not so much. anaanymous
Read More At : 14" Band Saw with Stand...

Powermatic Band saw 143, when i press the start button the saw turns on but wont stay on. When i release the start button the saw turns off. What is the problem. Please help. Thank You, Lee.

Your powermatic band saw has a Magnetic motor starter. Since it is hard to find parts for the 143 you can remove the power and take the starter apart and clean the contacts. If that fails you can take it off and take it to a Electrical Supply Store and have them match you up with one that will work.The way the switch works is when you push the on button it picks a relay that starts the motor and also has a contact the holds the relay picked. when you push the stop button it drops the circuit. This is a safety feature to prevent the motor from restarting after a power failure until you hit the button Hope this answers all your questionsPlease remember to Rate/vote for any solution that helps you out.Thanks for using Fixya.
Read More At : 143 14inch Band Saw Operateparts Manual...

I have a Tradesman model 8116 band saw. the wheel that turns the belt is now moving foward and prevents the bandsaw wheel that hold the blade from turning or spinning

Read More At : Saws...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0573 seconds