Guide :Saws : 10" Table Saw

No book.how to square craftsman table saw mod 137 blade to table

I lost my book on Model# 137.248830 Craftsman table saw. Trying to remember how to square the blade to the table. I have it mounted on a Craftsman stand w/sawdust bag. Do I have to disconnect it from the stand to get at the adjustment? BP

Research, Knowledge and Information :


"craftsman 10 in. table saw table saws" - Sears


"craftsman 10 in. table saw table ... Bosch 4100-09 10-Inch Smart Guard Square Lock Soft Start Worksite Table Saw Kit ... Craftsman CM 10IN' TILE SAW BLADE (2) ...
Read More At : www.sears.com...

Craftsman Saw: Get Power and Precision with Sears


A Contractor Grade Craftsman Saw This Craftsman table saw delivers ... Rail, Miter Gauge, Saw Blade, Rip Fence. Fence ... under the table to square saw up.
Read More At : www.sears.com...

Craftsman - Official Site


The Future of Craftsman starts now. Shop Craftsman Tools, Storage, Lawn & Garden Equipment and more.
Read More At : www.craftsman.com...

Operator’s Manual 10 in. COMPOUND MITER SAW Model No. 137.212360


10 in. COMPOUND MITER SAW WITH LASER TRAC® Model No. 137.212360 ... www.sears.com/craftsman Part No. 13721236001 ... No MITER SAW BLADE Rotating Table: ...
Read More At : download.sears.com...

137.248880 Craftsman 3 HP 10 Inch Table Saw - Hammerwall


137.218040 Craftsman 3.0 HP 10 in. Blade Table Saw... 137.218240 Craftsman 3.0 HP ... TABLE SAW Model No . 137 ... square on the table and against the blade ...
Read More At : www.hammerwall.com...

Craftsman Power Tool Parts | Great Selection | Great Prices ...


Table Saw Parts. Tile Saw Parts. Tiller Parts. Trimmer Parts. Utility Cart Parts. ... Customer Experiences I found parts for my 30 year old craftsman chain saw here, ...
Read More At : www.ereplacementparts.com...

Free Craftsman Saw User Manuals | ManualsOnline.com


Craftsman Saw 137.218030. Craftsman Table Saw with Stand Operator's Manual. Pages: 30. See Prices; ... Craftsman Table Saw with Stand Operator's Manual. Pages: 30.
Read More At : powertool.manualsonline.com...

Craftsman Parts | Sears PartsDirect


Shop the best selection of Craftsman repair parts for every product at Sears PartsDirect. Find parts, manuals & diagrams for any Craftsman repair project.
Read More At : www.searspartsdirect.com...

Suggested Questions And Answer :


No book.how to square craftsman table saw mod 137 blade to table


Thanks for using Fix YaTo download the owners manual for your saw, click --->here<---Please take the time to give this solution a fix ya rating.clarkco
Read More At : 10" Table Saw...

Craftsman model 708100 table saw tilt lock won't stay locked


Try removing the lock knob and putting a toothed lockwasher on the shaft. reinstall the knob.
Read More At : 10" Table Saw...

Table Saw Blade Won't Cut Straight


Inside the saw, on the end of the trunnion is a stop that is adjustable to zero the saw in to exactly 90 degrees. Either there is sawdust or something accumulated there or it needs to be adjusted. You say you cleaned it out, So you'll need to unplug it an have a look up in there. See how there's a geared piece of steel that moves when you crank the saw over to 45 degrees. Usually there's a bolt or stud with a locking nut on it, either on the trunnion itself or the lower surface of the table top. You need to break the nut loose and screw the bolt in or out to adjust, then crank the saw over to hit it, check for square with a known square, crank it all the way out of the way and readjust, etc. Until you get it right. Make sure to tighten that lock nut when you're done. I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread. If I've managed to answer your question or solve a problem, please take a moment to kindly rate this post....thanks!
Read More At : 10" Table Saw...

Re furbish old Craftsman 10'' table saw


It all depends on how much patience you have. It will cut ok, if you feed slowly and use a rip blade to rip with instead of a combination blade. (Buy one with only 36 teeth or 40 teeth). A sharp blade is always a lot easier and safer to use than that old rusty thing that is trying to grind its way through a piece of 2X. Another tip you might try is to put a coat of paste wax on the blade before you start. It will help if there's a lot of pitch building up as you cut. Otherwise, more hp will be less likely to bog down and overheat, and will allow you to push through denser and harder woods without the danger of overpowering the motor. But even then, a sharp rip blade is a wonder and a joy to use!
Read More At : Craftsman...

12" craftsman table saw 0 to 45 deg adjustment gears striped


Sears has a site for parts and owner manuals at www.ManageMyHome.com.It could be something is just loose and out of adjustment so that the teeth were able to slip on the gear. But I've never had a look at one of those to say for sure...oil always helps these things move easier...
Read More At : Saws...

I have a craftsman table saw model 137.248830 and the blade is out of square with the miter. How do I adjust it?


You should have 4 bolts holding the trunnion on to the table, just loosen these bolts up a little, tap the trunnion with a hammer, the right way, put a straightedge on the blade fully extended and measure across the table to a dado slot, front and rear, tap it till it is exact, tighten bolts and check again. This should do it. You can check your fence the same way. hope this helps.
Read More At : 10" Table Saw...

The blade isnot square with table - Craftsman 10" Table Saw


You can adjust the trunnion assembly from the bottom side of the table. Most saws have 6 bolts that bolt to bottom of top. if you loosen all six bolts then shift as nessessary to align to top top, then retighten the bolts. The holes in the trunnion assembly brackets should be oblong to allow this ajustment, Jim
Read More At : 10" Table Saw...

Truing craftsman table saw blade


Use a carpenter square to allign the blade both vertically and horizontally with your guide. This works very well.
Read More At : Saws...

Adjusting Blade/Miter Groove Alignment on 1950's Craftsman Table


Try using a 1/16 thick flat washer as a shim where the mounting bolts/trunions mate with table. 1/16 shim on front mounting bolt will shift front of blade over 1/16 or 1 on the back mounting bolt will shift back of blade over
Read More At : 10" Table Saw...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.powertoolz.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0775 seconds